Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

help with new radiator,

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 396
Joined: Tue May 12, 2009 3:03 pm
Location: Sunshine coast

help with new radiator,

Post by Middo »

Well its about that time wen iv put about 10 kilos of stop leak in my 4runners radiator but its swiss cheese like appearance just wont tolerate it anymore.
Im going to replace it in the very near future but im not sure if i should just buy a replacement stocko one or upgrade it.
This brings on my next question. What types of upgrades are there? Cause im not realy sure what im looking for.
I want something that will keep my engine realy cold cause it loves overheating in deep sand.
So let us know ur opinion?

Edit: would a nice big intercooler do much. (for temperature. i dont have a turbo or supercharger)

cheers, Tim
4x4 tool kit: Duct tape and a BFH . If it moves and it shouldn't, use the tape, if it doesn't move and it should, use the hammer.
Tim
User avatar
JWB
Posts: 451
Joined: Sun Aug 24, 2003 5:48 pm
Location: Logan

Post by JWB »

What motor is it?
what history do you know about it?
What have you replaced in the cooling system?

I have never seen a NA motor fitted with an intercooler?

You might have a mess in there with all that stop leak :?

cough up $$$ for a new radiator, give the system multiple flushes

and you might be lucky :D

the standard rad should be fine! ( apart from known issues with any particular engine )

cheers
JB
Posts: 396
Joined: Tue May 12, 2009 3:03 pm
Location: Sunshine coast

Post by Middo »

sweet as. its a recon engine 13000 ago. realy good engine. just the radiator is up the shitter. ill probably go with a new stocko one.
4x4 tool kit: Duct tape and a BFH . If it moves and it shouldn't, use the tape, if it doesn't move and it should, use the hammer.
Tim
Posts: 19062
Joined: Sat Oct 25, 2003 11:39 pm
Location: In a horse near you

Post by chimpboy »

Middo wrote:ill probably go with a new stocko one.
That's what I would do.
This is not legal advice.
User avatar
JWB
Posts: 451
Joined: Sun Aug 24, 2003 5:48 pm
Location: Logan

Post by JWB »

Middo wrote:sweet as. its a recon engine 13000 ago. realy good engine. just the radiator is up the shitter. ill probably go with a new stocko one.
M2c
get a new radiator ASAP before you send your good motor
to an early grave
:oops:
And I meant what type of engine, ie 4 cyl petrol, 4 cyl diesel or v6 petrol??
or other??
JB
Posts: 2585
Joined: Fri Mar 28, 2008 4:45 pm
Location: SYDNEY

Post by thehanko »

JWB wrote:
Middo wrote:sweet as. its a recon engine 13000 ago. realy good engine. just the radiator is up the shitter. ill probably go with a new stocko one.
M2c
get a new radiator ASAP before you send your good motor
to an early grave
:oops:
x2
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Posts: 5256
Joined: Fri Jun 16, 2006 6:49 pm
Location: Melbourne

Post by Struth »

Yep stock motor should equal stock radiator in a 4 Runner. Their cooling systems should more than adequate for our conditions, unlike a Surf.

Cheers
Posts: 396
Joined: Tue May 12, 2009 3:03 pm
Location: Sunshine coast

Post by Middo »

haha my bad. its 3.0L v6 petrol. from the sounds of it stock as a rock is the go. cheers guys
4x4 tool kit: Duct tape and a BFH . If it moves and it shouldn't, use the tape, if it doesn't move and it should, use the hammer.
Tim
Posts: 619
Joined: Thu Nov 03, 2005 11:20 am
Location: vic

Post by Hamo »

stick a toyota thermostat in it while your there ;)
[quote="RN"]So do you support your local vendor...not if it is going to cost me almost double. [quote]
Posts: 396
Joined: Tue May 12, 2009 3:03 pm
Location: Sunshine coast

Post by Middo »

yeh will do
4x4 tool kit: Duct tape and a BFH . If it moves and it shouldn't, use the tape, if it doesn't move and it should, use the hammer.
Tim
Posts: 292
Joined: Wed Jan 11, 2006 11:49 am
Location: Seville Vic

Post by MICK77 »

As mentioned above, I would flush the system many times to get the stop leak out. That sh1t is only going to give you dramas!

Cheers,

Micko
[quote="bogged"]
Whats that old saying that I've modernized for this scenario
"fuked over once, shame on her, fuked over twice, shame on me."
(c) Bogged 2008[/quote]
Posts: 396
Joined: Tue May 12, 2009 3:03 pm
Location: Sunshine coast

Post by Middo »

could b a very noob question but how do u flush the system?
4x4 tool kit: Duct tape and a BFH . If it moves and it shouldn't, use the tape, if it doesn't move and it should, use the hammer.
Tim
Posts: 5714
Joined: Fri Nov 22, 2002 3:55 pm
Location: Perth WA.

Post by nicbeer »

Middo wrote:could b a very noob question but how do u flush the system?
Stick a hose in the hose and flush all the crap out.

a few reverse flushes, IE: reverse the directioin of the flow normally, im not sure which way normally goes in the runner etc.

Most afterwards run it up with plain distilled water and then dump it to take any of the tap water out of the system and then refill with the correct coolant/distilled.

BTW toyota coolant is exxy but many say it is the best etc.
[url=http://www.outerlimits4x4.com/viewtopic.php?p=930942#930942&highlight=]Zook[/url]
U SUK Zook Built and Sold.
New rig is 97 80 DX. 2" list 33s
Posts: 396
Joined: Tue May 12, 2009 3:03 pm
Location: Sunshine coast

Post by Middo »

cheers
4x4 tool kit: Duct tape and a BFH . If it moves and it shouldn't, use the tape, if it doesn't move and it should, use the hammer.
Tim
Posts: 396
Joined: Tue May 12, 2009 3:03 pm
Location: Sunshine coast

Post by Middo »

cheers
4x4 tool kit: Duct tape and a BFH . If it moves and it shouldn't, use the tape, if it doesn't move and it should, use the hammer.
Tim
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests