I have just picked up a 86 NT sierra and am looking at running 31's for the time being.
I will be putting in a 1lt transcase to lower the gearing but I also have the 1lt diffs.
Now I know the 1lt diffs are 4.1 's and the NT's are 3.9 so the 1lt diffs would be better for the gearing.
But how are the 1lt diff for strength. I think someone once told me they were not as strong as the 1.3 diffs.
Also if they are a bit weaker, are the diff centres for these two interchangable as I think I remember reading that they may not be.
i wish I had a better memory!!!!!!!!!!!!!!!!!!!!!!!!!!!
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Diff strength
Wolverine wrote:Cool thanks! I am going welded diffs anyway so I wont have to worry about lockers.
I will soon have some birfields, there shouldn't be any dramas with those though, will there?
dont know much about birfields, both my diffs are welded, I run a 1.3 motor into my 1.0 litre gearing, it pulls 31's OK...hopper be better, but that relies on winning lotto.. also the extra clearance under the 1 litre diffs is great, christover
4WD SUZUKI CLUB VICTORIA
http://www.vic.suzuki4wd.com/forum/
http://www.vic.suzuki4wd.com/forum/
Wolverine wrote:so to keep things cheap do you reckon I change over to the 1lt diffs for better gearing or is this a backwards step.
Another option I have is the rocklobster conversion as I now believe the 1lt case I have is a 84 so I just need to find someone who does it over in Perth.
Any thoughts
the difference between 3.9 and 4.1 wont be worth the trouble, but the extra diff clearance is very good. I'd stick to the 1.3 diffs with 1.0 transfer case. rocklobster is just 2 sets of gears welded together I think. not a very reliable outcome, as 2nd hand 4:1 rockhoppers are now getting cheaper, as the money guys want 6:1 hoppers.
4WD SUZUKI CLUB VICTORIA
http://www.vic.suzuki4wd.com/forum/
http://www.vic.suzuki4wd.com/forum/
speaking of diff strength, has anybody ever run 35x15x15 boggers in WT diffs? how long did they last?
Myself and greg are running 34 x 9.50 swampers with low gearing and lockers and haven't broken them yet (I have had this setup for a few yearsd and greg a couple) Bigsteve has just put 34 x 10 on his but hasn't tested them yet and love_mud has 35 claws on his.
In Melbourne and our conditions of more mud and low traction surfaces you should be ok as long as you don't flog the living crap out of it. On rock or high traction surfaces you would probably find the strength to be lacking[/quote]
Ransom note = demand + collage
[/quote]grimbo wrote:Dawg wrote:speaking of diff strength, has anybody ever run 35x15x15 boggers in WT diffs? how long did they last?
Myself and greg are running 34 x 9.50 swampers with low gearing and lockers and haven't broken them yet (I have had this setup for a few yearsd and greg a couple) Bigsteve has just put 34 x 10 on his but hasn't tested them yet and love_mud has 35 claws on his.
In Melbourne and our conditions of more mud and low traction surfaces you should be ok as long as you don't flog the living crap out of it. On rock or high traction surfaces you would probably find the strength to be lacking
Dawg, If you find that they are no good - give them to me and i will work out how to run them
DMA Founding Member #1 - Now Retired
[/quote]grimbo wrote:speaking of diff strength, has anybody ever run 35x15x15 boggers in WT diffs? how long did they last?
Myself and greg are running 34 x 9.50 swampers with low gearing and lockers and haven't broken them yet (I have had this setup for a few yearsd and greg a couple) Bigsteve has just put 34 x 10 on his but hasn't tested them yet and love_mud has 35 claws on his.
In Melbourne and our conditions of more mud and low traction surfaces you should be ok as long as you don't flog the living crap out of it. On rock or high traction surfaces you would probably find the strength to be lacking
I have run 33x12.5 swampers and 35x12.5 claws for a while now, the biggest issue I have found is actually fatuige over time.. IE cracking the diff housing in a horizontal plane... most just stress from torque applied over the past 80,000kms I have run with 32's and bigger.
If your sensible they should last OK .. (depending on the surface your running on as well like grimbo said)
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Dick wrote:Oh I see..
Did u know that Vitara front diff will bolt into Sierra rear hsg .. Seen one yesterday, for what its worth...
They do .. but due to the marginal strength of the alloy housing on the majority of vit diffs.. on a modified sierra they are begging for expensive trouble
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
love_mud wrote:Dick wrote:Oh I see..
Did u know that Vitara front diff will bolt into Sierra rear hsg .. Seen one yesterday, for what its worth...
They do .. but due to the marginal strength of the alloy housing on the majority of vit diffs.. on a modified sierra they are begging for expensive trouble
Why would Suzuki ever make a diff with Alloy housing.. got me stuffed.. My GV steel one is being assembled now, complete with A/L and I am adding an extra mount to be safe.. Next problem C/V's I assume !
05 Patrol GU ST Ute
3" lift, 3" exhaust, custom Garrett BB Turbo and top mount.. and electric mirrors !
3" lift, 3" exhaust, custom Garrett BB Turbo and top mount.. and electric mirrors !
Dick wrote:love_mud wrote:Dick wrote:Oh I see..
Did u know that Vitara front diff will bolt into Sierra rear hsg .. Seen one yesterday, for what its worth...
They do .. but due to the marginal strength of the alloy housing on the majority of vit diffs.. on a modified sierra they are begging for expensive trouble
Why would Suzuki ever make a diff with Alloy housing.. got me stuffed.. My GV steel one is being assembled now, complete with A/L and I am adding an extra mount to be safe.. Next problem C/V's I assume !
Lighter = better fuel economy, the only reason I can think of ..
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
What breaks first? the chicken or the egg?
Seriously the IFS alloy front end has to be substantially lighter than the widetrack front end, with the benefit of 5" more width.
If I get around to ripping all the bits out in the near future I'll weigh them.
there was at least SOME method in the madness I am sure.
Seriously the IFS alloy front end has to be substantially lighter than the widetrack front end, with the benefit of 5" more width.
If I get around to ripping all the bits out in the near future I'll weigh them.
there was at least SOME method in the madness I am sure.
Who is online
Users browsing this forum: No registered users and 48 guests