Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

axles too long? help please

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Posts: 206
Joined: Tue Apr 12, 2005 1:59 pm
Location: Rockhampton QLD

Post by Pauwolf »

Chucky wrote:Is the circlip really needed?


You need to stop the axle drifting in and out, in a toyota, it really needs to run hard up against the bronze bush so there are 2 ways to do this

1. run the circlip
2. martack - put a little tack weld on the axle spline so that it cannot go into the spider gear any further than necesary

unless you are breaking CVs all the time, (ie comps) i would go with option 1

ps in a nissan you can get away with not running a circlip because of the design, however not advisable in a toyota

Paul[/quote]
91 FJ 80 Project on the go - air lockers, 3in lift, super duper 3F, 36" pedes, toyota V8 getting prepped now
Posts: 292
Joined: Wed Jan 11, 2006 11:49 am
Location: Seville Vic

Post by MICK77 »

Chucky wrote:I cant beleive they gave it back to you like that.
Looks like they just threw it together so they could get it out the door and have a early knockoff before Xmas
Agreed!!!

If that was my handy work, I'd take myself out the back & slap myself stupid for it! That's a farkin' disgrace! I wouldn't let those farkers touch a tricycle!

Any competent mechanic or DIY guy can do this job. This is nothing more than pure incompetence at it's best.

If I was you, I would find a new mechanic or grab a w/shop manual and give it a go yourself! What ever you do, don't ever take another vehicle there again.

Cheers,

Micko
[quote="bogged"]
Whats that old saying that I've modernized for this scenario
"fuked over once, shame on her, fuked over twice, shame on me."
(c) Bogged 2008[/quote]
Posts: 44
Joined: Mon Aug 31, 2009 5:57 pm
Location: All over the place

Post by moose2367 »

Chucky wrote:Is the circlip really needed?

All my cruisers have been 2nd hand, and none of them have had the circlip in, so I didn't bother either and never had a problem. I do put a front hub kit through my cruiser every 18 months to 2 years. I also rip the cv's out every 6 months to repack with grease along with my wheel bearsings. I have only ever blown 1 CV before in an unlocked car due entirely to my driving style. Changed that, and with lockers I haven't blown a cv yet.....worn a few out and changed due to clicking etc, but never blown one on the track.
If you've got a Cruiser then there is no need to pull out the Cv's to grease them. There is a square plug on the knuckle, use a 13mm spanner to undo and pump grease in with a grease gun, the fitting fits just right. No need to put a kit through unless they're visibly leaking, just wasting money.

Cheers
Posts: 6029
Joined: Tue Dec 24, 2002 9:34 pm
Location: South Australia

Post by bad_religion_au »

moose2367 wrote:
Chucky wrote:Is the circlip really needed?

All my cruisers have been 2nd hand, and none of them have had the circlip in, so I didn't bother either and never had a problem. I do put a front hub kit through my cruiser every 18 months to 2 years. I also rip the cv's out every 6 months to repack with grease along with my wheel bearsings. I have only ever blown 1 CV before in an unlocked car due entirely to my driving style. Changed that, and with lockers I haven't blown a cv yet.....worn a few out and changed due to clicking etc, but never blown one on the track.
If you've got a Cruiser then there is no need to pull out the Cv's to grease them. There is a square plug on the knuckle, use a 13mm spanner to undo and pump grease in with a grease gun, the fitting fits just right. No need to put a kit through unless they're visibly leaking, just wasting money.

Cheers
that doesn't repack the grease IN the cv, just the grease the cv runs in in the knuckle housing
Spit my last breath
Posts: 4825
Joined: Sun May 04, 2003 6:33 pm
Location: Berwick vic

Post by droopypete »

This is the best way to grease your CV's.
http://www.gearingdynamics.com/greasecv.htm
Cable bracing is the way of the future!

v840 said "That sounds like a booty fab, hack job piece of shit no offence."
Posts: 4825
Joined: Sun May 04, 2003 6:33 pm
Location: Berwick vic

Post by droopypete »

Just a thought on your axle issue, cast your mind back to when you dropped your car off, do you remember if they were also working on a IFS land cruiser at the same time :idea:

Peter.
Cable bracing is the way of the future!

v840 said "That sounds like a booty fab, hack job piece of shit no offence."
Posts: 655
Joined: Thu Mar 20, 2008 12:51 pm
Location: melbourne

Post by Jacked »

is that spacer really homemade? looks like it has been in there for a while.
maybe its supposed to be on the inside next to the cv.
Posts: 47
Joined: Thu Jun 18, 2009 3:04 pm
Location: Bunbury

Post by 350HJ75 »

yeah the spacer is homemade, can see it has been cut with a grinder, and i have never seen it before in there since owning the car
Posts: 750
Joined: Fri Oct 17, 2003 9:07 pm
Location: Albury

Post by MUD000 »

Should also be a clip that holds the brake line in place :D
If its all back together properly then my guess would be differant cv (full time 80 series one
My 2c as I'm no mechanic either but I'll give things ago
Cheers Dan
06 Dual Cab Hilux Loaded with ARB
80 Series With L98 6ltr 35's 4L80E Locked & Loaded
84 Extra Cab Hilux Build up fun car
96 Dual Cab Hilux build up Long range play car
www.trailtrack4x4.com
Posts: 47
Joined: Thu Jun 18, 2009 3:04 pm
Location: Bunbury

Post by 350HJ75 »

ok well the ute is fixed, the Cv was wrong the whole time so now i have bought a new cv for 250 and they installed it for free. im just happy its going again now.
Posts: 43
Joined: Wed Sep 24, 2008 2:36 pm
Location: perth

Post by rusty bus »

So the CV was just floating around in the housing/stub axle all that time?? surprised it didnt hammer the bronze bush that the cv butts up against a bit. I say good on them for making a spacer to counteract the problem. At the same time i say SHAME ON THEM for making a band aid fix on something which is quite clearly not right, and then to send it off without the locking hub assembled.....come on thats just ridiculous. I can only imagine how the mechanic who served you your keys was feeling when he had to explain to you that your car wasnt assembled as he took your hard earned coin.....
Posts: 1912
Joined: Sat Feb 14, 2009 7:15 pm
Location: VIC

Post by beinthemud »

So You Drove it in there
They fixed it
Assuming it had the Right CVs to start with
Then you had to go Buy new CVs to Replace the Old CVs that were Correct in the car in the First Place ,But hey thats nice of them to Fit them for free,
I Guess One is Born Everyday
Manuels= 4wd,cars,bikes,guns,trucks,race cars
Automatics=washing machines,dish washers,fridges
Posts: 47
Joined: Thu Jun 18, 2009 3:04 pm
Location: Bunbury

Post by 350HJ75 »

it had one wrong cv to start with, which flogged out that brass bush. which was only highlighted when they tires to put it back together. and yeah there was some discounts given cos they could not fix the problem initially. and only problem was i ddnt pick up the car myself first time so was not there to say wtf?
Post Reply

Who is online

Users browsing this forum: No registered users and 10 guests