Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Thud or clunck on take off? 100 Series
Moderators: toaddog, Elmo, DUDELUX
Thud or clunck on take off? 100 Series
Hey guys,
I have just purchased a 100 series 99 model snowy and I love it ! However it does have a small thud or clunk that you feel when you are taking off from a stand start? It is very slight and it does not happen everytime?
I searched this forum and noticed that the 200 series has what i think may be a similar thing. From what I have gathered it seems to have something to do with the tailshaft?
Can anyone else give me some ideas or inform me a little more about this? Is this a "big" problem? Will this effect something else if not fixed straight away?
I have just purchased a 100 series 99 model snowy and I love it ! However it does have a small thud or clunk that you feel when you are taking off from a stand start? It is very slight and it does not happen everytime?
I searched this forum and noticed that the 200 series has what i think may be a similar thing. From what I have gathered it seems to have something to do with the tailshaft?
Can anyone else give me some ideas or inform me a little more about this? Is this a "big" problem? Will this effect something else if not fixed straight away?
[/quote]sickgm wrote:Thanks guys,
z()ltan "drive shaft uni joints
drive shaft spline
diff backlash"
Is this a major issue? will it effect the rest of the drive line and cause something to go wrong?
I just need to know if I can drive the car back to NSW from Vic?
get under the car and grab your tail shafts front and rear at each uni joint or slip point and try to shake or wobble them, there should be minimal or no play.
if a uni joint has had it and you drive it a long way it could flog out and drop your drive shaft onto the hwy which could get messy. though unlikely.
play in the splines is not likely to cause major issues on your drive unless its excessive. but will get worse with driving.
both of these issues would also be likely to be giving you some wheel balance type wobbles at higher speeds, often on overrun - like when you back of the gas at 100 or so.
if its a bush it should be fine for the drive but sort it soon.
I would personally probably drive it without a second thought and sort it at home. but thats just me.
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Goto *
i would be looking at lower control arms get under and have a look at the bushes at both ends
i have this problem with my 80 series
cheers
i have this problem with my 80 series
cheers
R.I.P. Darryl "DAZZA" Mutch 02/08/1978 - 26/08/2012 aged 34 years ... You will be missed my little brother.
http://www.outerlimits4x4.com/viewtopic.php?f=16&t=39190&start=150
http://www.outerlimits4x4.com/viewtopic.php?f=16&t=39190&start=150
I have a similar thud in my hilux (IFS). Its mainly noticeable when turning slightly on take off. IE turning right from a stop sign. Also does it when your turning into a driveway. It is a scarey noise. The only thing I havn't recently replaced up front is the Upper control arm bushes. Mainly as it is a prick of a job.flyinwall wrote:i would be looking at lower control arms get under and have a look at the bushes at both ends
i have this problem with my 80 series
cheers
On my last trip to pedders I was advised they were on the way out so i'm hoping they are the problem.
Not sure if your 100 has a similar setup to my hilux, if so, i'd be checking these out.
depending on the shaft design, too much grease in the slip spline can cause the two parts to jack out and put alot of load on output/pinion bearings.
The shaft will usually have a grease relief point in there for this but they sometime get clogged up and dont work.
The shaft will usually have a grease relief point in there for this but they sometime get clogged up and dont work.
Locktup4x4.com.au - For all of your hardcore gear
Outlaws4x4.com
Outlaws4x4.com
Just grease the uni's till you see it purge the seals, and the slip joint should only take bout 3-4 pumps every 5000klms or service intervils.
4x4 Suspension & Accessories- (07)5549 0056
Unit 2/76 Blanck Street Ormeau QLD 4208
www.southerncross4x4.com
Distributors of Tough Dog Dobinsons Superior Engineering Products ProComp EFS & Tmax
Unit 2/76 Blanck Street Ormeau QLD 4208
www.southerncross4x4.com
Distributors of Tough Dog Dobinsons Superior Engineering Products ProComp EFS & Tmax
Who is online
Users browsing this forum: No registered users and 3 guests