Just changed the front springs on the young blokes Hilux.
The problem is the new springs are 6 leaf vs. original 5 leaf. The height of the spring packs at the centre bolt is 45mm vs 34mm of the old ones.
The problem is that now the drag link fouls the rear U bolt when you turn the wheels to the right. This happens just off centre.
Wouldn't have a clue what the new springs are as they came with the truck (not fitted). They look well made. They have a code on them: TOYO10 CD/S- any ideas brand etc?
I didn't notice the clearance with the old springs but given the new ones are only 11mm higher I guess it wasn't much.
Any ideas for a fix? Anything we might have missed?
Thanks.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
HELP!! Hilux LN65 Front Springs
Moderators: toaddog, Elmo, DUDELUX
Yeah used a flat U bolt (even tried the old one). Is the drag link supposed to run beside the spring/U bolt or above it? The new springs are the same width as the old ones just 11mm higher due to the extra leaf and probably thicker leaves I guess.
I had a play around with it later this afternoon- eg. made sure the spring and U bolt were as far inboard as I could- the end of the draglink still hits the U bolt- not just grazes it but butts against it!
Looks like it's a tight fit at the best of times! I didn't take much notice of how close it was when removing old springs.
Starting to think it could be the steering arm be bent a little or is this always an issue when fit heavy duty ie. thicker springs?
How close is anyone elses drag link to spring/Ubolt clearance either standard or with HD springs?
I had a play around with it later this afternoon- eg. made sure the spring and U bolt were as far inboard as I could- the end of the draglink still hits the U bolt- not just grazes it but butts against it!
Looks like it's a tight fit at the best of times! I didn't take much notice of how close it was when removing old springs.
Starting to think it could be the steering arm be bent a little or is this always an issue when fit heavy duty ie. thicker springs?
How close is anyone elses drag link to spring/Ubolt clearance either standard or with HD springs?
FIXED IT!
-Fitted draglink kit both ends to get rid to make sure pins were centred
-reversed draglink so short end was at steering arm end
-loosened spring centre bolt and tapped spring leaves to make sure they were in line and as far as possible to the centre of the axle
Now have about 3-4mm clearance to the U bolt when turning left. BTW- found out that some people have 2-3mm on standard vehicles in good nick! Some who checked even found theirs making contact.
Once you have max clearance, make sure grease boot spring retainers are positioned so ends are away from U bolt.
I'm amazed at what I turned up:
-people have had no left turn due to slight wear in swivel hub bearings or draglink ends.
-a local mechanic to me fouling the U is not uncommon and can be difficult to fix.
So dissappointing that Toyota designed this so dangerous when it would have been so easy to get at least 100mm clearance with better design- there's plenty of room in that area. Specially on a 4WD where sticks and rocks etc could easily jam in such a small clearance.
-Fitted draglink kit both ends to get rid to make sure pins were centred
-reversed draglink so short end was at steering arm end
-loosened spring centre bolt and tapped spring leaves to make sure they were in line and as far as possible to the centre of the axle
Now have about 3-4mm clearance to the U bolt when turning left. BTW- found out that some people have 2-3mm on standard vehicles in good nick! Some who checked even found theirs making contact.
Once you have max clearance, make sure grease boot spring retainers are positioned so ends are away from U bolt.
I'm amazed at what I turned up:
-people have had no left turn due to slight wear in swivel hub bearings or draglink ends.
-a local mechanic to me fouling the U is not uncommon and can be difficult to fix.
So dissappointing that Toyota designed this so dangerous when it would have been so easy to get at least 100mm clearance with better design- there's plenty of room in that area. Specially on a 4WD where sticks and rocks etc could easily jam in such a small clearance.
Who is online
Users browsing this forum: No registered users and 2 guests