hey hey i need some info i have a 97 lux with 2.8 turbo diesel i really wanna upgrade engine ultimate option would be 1uzfe 4 litre i think they nice revving and nice and light for the hilux i have crawler gears, f/r air locks and dirty 30's. can any1 help in what i will need and where to source adaptor plates and anything needed to proceed, [can hilux v6 bellhousings fit ect.]
any input would be great cheers
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
i wanna v8 my lux
Moderators: toaddog, Elmo, DUDELUX
hi there
im relatively new on here but im not new to toyotas
as such there are no manual 1UZ's out there, (soarers and the like always had autos behind them) so any manual conversion bits n peices are going to have to be a custom creation but im lead to believe niteparts in NZ does a bellhousing to suit. also depends if your gearbox is a W5x or a R15x style box. alternatively a tremec TKO could be tasty although ghastly expensive.
secondly you would need to address the engine mounts, easy enough to make if you are handy with a welder.
then the wiring. Wiring can be a nightmare of a task, esp for a beginner who hasnt done an engine conversion before, but it can also be a nightmare for the seasoned
budget also comes into it, whatever you think you will spend double it and in some cases triple it.
but yeah, thats about all of the top of my head. the 1UZ's are an absolutely bulletproof engine, whether or not the will be better than a diesel offroad it debatable. the 1uz while having more capacity, wont have the low down torque that the 3L has. but the 3L has a significantly lower rev range and a hell of a lot less killerWasps
im relatively new on here but im not new to toyotas
as such there are no manual 1UZ's out there, (soarers and the like always had autos behind them) so any manual conversion bits n peices are going to have to be a custom creation but im lead to believe niteparts in NZ does a bellhousing to suit. also depends if your gearbox is a W5x or a R15x style box. alternatively a tremec TKO could be tasty although ghastly expensive.
secondly you would need to address the engine mounts, easy enough to make if you are handy with a welder.
then the wiring. Wiring can be a nightmare of a task, esp for a beginner who hasnt done an engine conversion before, but it can also be a nightmare for the seasoned
budget also comes into it, whatever you think you will spend double it and in some cases triple it.
but yeah, thats about all of the top of my head. the 1UZ's are an absolutely bulletproof engine, whether or not the will be better than a diesel offroad it debatable. the 1uz while having more capacity, wont have the low down torque that the 3L has. but the 3L has a significantly lower rev range and a hell of a lot less killerWasps
I did it about 5 years ago (91 4runner) you can get bellhousing, clutch, flywheel etc from Dellows or Castlemaine Rod shop. Engine mount I'm not sure if you can get them off the shelf now but they are not difficult to make.
As for the wiring there is about 10 wires from memory that need to be wired up and a few little things extra (mine was V6 so had most of the stuff that the Diesel won't). It is not to difficult to do
Mine cost about $6000 all up including new Rad, engineering etc........
I did most of it myself which helps with the cost
As for the wiring there is about 10 wires from memory that need to be wired up and a few little things extra (mine was V6 so had most of the stuff that the Diesel won't). It is not to difficult to do
Mine cost about $6000 all up including new Rad, engineering etc........
I did most of it myself which helps with the cost
if it ain't broke send it to me i'll fix it!
Hi i too want to do the same conversion as i have got a 253 in my current hilux and want a change ,can you tell me if there is any hickups to watch out for if i was to proceed with it..i can handle the wiring side of things as this is what i do for a living but knowing the right combination of using the right radiator ,clutch ,keep it manual or auto?,etc etc any hints would be great ,or anyone in brissy that can head me in the right direction would be great.....
i been enquiring to killalux [QLD] and he can do the loom he has helped out heaps with info to finding things needed he say using the 1u loom he can root around with it make it pretty and stand alone for about 650 bucks that to me sounds great so now i have that info i gonna go ahead and source bellhousings and soforth
http://www.rodshop.com.au/pricelists/LEXUS_1UZ.pdf
if i cant find a cheaper one i'll be just doin this
if i cant find a cheaper one i'll be just doin this
All i can say is "DONT GIVE CASTLEMAIN ROD SHOP ANY MONEY" they will rip you off, thats what they are good at, try and get your money back when they are in a different state of Aust, you wont and they know that and they continue to rip people off. 
Try Ichiban Imports in Moorebank,Sydney, i have purchased Lexus engines on several occasions with happy results and they "WONT" rip you off...
Try Ichiban Imports in Moorebank,Sydney, i have purchased Lexus engines on several occasions with happy results and they "WONT" rip you off...
Who is online
Users browsing this forum: No registered users and 6 guests