Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Please Delete.
Please Delete.
..
Last edited by Straussy on Mon Feb 01, 2010 6:15 am, edited 2 times in total.
Cheers, Straussy.
I did not have LPG, some of this setup was designed by krimnl, hoon and sandy
I ran a Vortech V1 S trim supercharger, custom made bracket, and pulley off the crank. Belt was a V belt, tensioner off a falcon if I remember correctly. The power steering resevoir also needed to be remotely mounted and a falcon one again was sourced. Also a PWR front mount intercooler.
Autronic computer, custom snorkel, airbox and intake. Bigger fuel pump and surge tank
You will definatley have more power and torque, I felt that my car was quicker through the bush than a lot of the turbo petrol's due to more useable power lower in the rev range
It was a bloody awesome car that is still going strong although I don't own it anymore.
It will be more expensive than a turbo but in my opinion much better.
The Crown supercharger would probably only be good for low boost which may be good, just depends how much power you want.
Your problem may be he dual fuel as I do not know if aftermarket computers can handle that but I have no knowledge of dual fuel at all. The standard EFI computer will need to be upgraded though if you do want to run fuel. That is the other expensive bit. I would budget on 10g for someone else to do the work and using quality components.
Rob
I ran a Vortech V1 S trim supercharger, custom made bracket, and pulley off the crank. Belt was a V belt, tensioner off a falcon if I remember correctly. The power steering resevoir also needed to be remotely mounted and a falcon one again was sourced. Also a PWR front mount intercooler.
Autronic computer, custom snorkel, airbox and intake. Bigger fuel pump and surge tank
You will definatley have more power and torque, I felt that my car was quicker through the bush than a lot of the turbo petrol's due to more useable power lower in the rev range
It was a bloody awesome car that is still going strong although I don't own it anymore.
It will be more expensive than a turbo but in my opinion much better.
The Crown supercharger would probably only be good for low boost which may be good, just depends how much power you want.
Your problem may be he dual fuel as I do not know if aftermarket computers can handle that but I have no knowledge of dual fuel at all. The standard EFI computer will need to be upgraded though if you do want to run fuel. That is the other expensive bit. I would budget on 10g for someone else to do the work and using quality components.
Rob
Still going hey, I tuned that for Hoon back around 2004? when he did his first Vic Winch, won it too.
Be careful of the small Jap blowers, the largest capacity one I know of is to suit a 2.4L engine. It needs to be spinning nearly twice as fast to make the same boost on a 4.2. At these blower speeds the outlet air temps become very high abd it is possible to exceed the blowers maximum RPM. I wouldn't put them on anything over 3.0L personally.
Joel
Be careful of the small Jap blowers, the largest capacity one I know of is to suit a 2.4L engine. It needs to be spinning nearly twice as fast to make the same boost on a 4.2. At these blower speeds the outlet air temps become very high abd it is possible to exceed the blowers maximum RPM. I wouldn't put them on anything over 3.0L personally.
Joel
-Pre trip inspections/ servicing
-Suspension/ custom modifications
-4wd Dyno & tuning
-Qualified mechanics
-Suspension/ custom modifications
-4wd Dyno & tuning
-Qualified mechanics
Maybe put your old qustion back so it doesn't look like Joel and I just made up some crap to post that was completely random and for future reference for others.
Also the new question has been asked numerous times, I would cut the gaurds and lower it. A good cut can look factory with a more standard look and no trouble from the police
Still going strong Joel, the new owner rarely drives it offroad but it still has blown diffs, thrown belts etc...waste of a car and motor. The intercooler you fitted though hasn't missed a beat
Take it easy mate
Rob
Also the new question has been asked numerous times, I would cut the gaurds and lower it. A good cut can look factory with a more standard look and no trouble from the police
Still going strong Joel, the new owner rarely drives it offroad but it still has blown diffs, thrown belts etc...waste of a car and motor. The intercooler you fitted though hasn't missed a beat
Take it easy mate
Rob
Was beggining to wonder what was going on here. Who is online
Users browsing this forum: No registered users and 129 guests