Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

UHF Reception Problems...

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 338
Joined: Wed May 23, 2007 6:11 pm
Location: Sydney

UHF Reception Problems...

Post by Buggerific »

Hi all,

I have an icom UHF in my zook, I'm getting about a car-length range out of it at the moment... I think it worked on the way home when I bought the car but I've since put on an alloy bar.

I've checked the connection of the cable from the plug to the base of the antenna and all is fine, I've tried a different whip on it with no success...

Do most, or some, antennas need to ground themselves through the bar and could this be my problem because the alloy bar doesn't conduct?

I appreciate any feedback!
Ozkor Auto Tech - 51 Orchard Road, Brookvale

1997 HZJ75 - 2" Springs, 33" MTZs, Touring Rig with more toys to come!
Posts: 2585
Joined: Fri Mar 28, 2008 4:45 pm
Location: SYDNEY

Post by thehanko »

yes some antennas grount through their mount, try a seperate wire back to the body, front under the antenna mount.
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Posts: 1990
Joined: Sun Jan 14, 2007 9:14 am
Location: Melbourne

Post by T_Diesel »

By the sounds of it, your antenna is "ground dependant" which is why it's not working with the change of bull bar. As suggested, find a suitable ground and wire your ground back to somewhere suitable.

I would also check the continuity across your coaxwith a multi-meter to make sure you have no leakage anywhere along the coax aswell.
Posts: 338
Joined: Wed May 23, 2007 6:11 pm
Location: Sydney

Post by Buggerific »

Yeah I have checked the continuity from the plug end to the base of the antenna and all is fine on both the pin and the ring and i've checked for continuity between the pin and the ring and they're not shorted out so that should be fine...

Will try a ground cable when it's not raining!


Cheers!
Ozkor Auto Tech - 51 Orchard Road, Brookvale

1997 HZJ75 - 2" Springs, 33" MTZs, Touring Rig with more toys to come!
Master of my own domain
Posts: 1516
Joined: Mon Apr 21, 2008 8:01 pm
Location: Shellharbour, NSW

Post by mike_nofx »

aluminium is a conductor by the way!
Posts: 280
Joined: Tue Feb 16, 2010 1:21 pm
Location: Werribee

Post by MrGrim »

ive been a CB/ham operator for nearly 3 decades

1st metal is metal alloy, steel, copper, brass, lead, ect it will all ground
( running a ground wire from the base to a ground point will incept harmonics not good !!! )
2nd you need to chech your coax at the plug end for :-
A- no short from pin to outer of plug
B- pin shows circut to antenna base thread
C- the outer does show circut to ground at both ends
D- 99% of all UHF Antennas are ground dependant unless marine they are co ground dependant or independant and normaly white

you have two other options replace the coax set there around $15-$20 or have a comms store check the SWR standing wave ratio
with a meter this will diiagnose if its the coax or the radio and re signal with out even the coax pluged in you should still get at least 20-100 mtr signal
(not recomended to transmit for long periods as its harmful to the radio but helpful to just test to check if radio has a problem with out test equipment)

still have any problems you can pm me ill try to help further
Cheers
Mark
71 fj40 front shackle reversal +3" , 55 rear springs +3", 35 15.5 claws , 60 diff's 4wheel disc's , SOON TO BE WINDSOR V8 + 5 speed
74 fj40 stock but very clean
84 bj40 3b stock and unloved
Posts: 338
Joined: Wed May 23, 2007 6:11 pm
Location: Sydney

Post by Buggerific »

As mentioned earlier, I have checked coax cable and all is good... The bar does conduct, I've now tested for that. Thought it was a valid question though.

Put a different radio in to test with all the same cables and it worked fine so there seems to be some sort of fault within my radio unit.

Receives better than it transmits but still not a good range at all.

Does anyone know if a radio repairer in Sydney... Preferably northern beaches/north shore?
Ozkor Auto Tech - 51 Orchard Road, Brookvale

1997 HZJ75 - 2" Springs, 33" MTZs, Touring Rig with more toys to come!
Posts: 338
Joined: Wed May 23, 2007 6:11 pm
Location: Sydney

Post by Buggerific »

So...

Pulled the unit out today to find some sort of oil over the outside of it... So I opened it up, there was a little but if oil on the inside and one of the capacitors (or something similar) has exploded. Damn.

So I am now looking for a radio repairer to take it to.
Ozkor Auto Tech - 51 Orchard Road, Brookvale

1997 HZJ75 - 2" Springs, 33" MTZs, Touring Rig with more toys to come!
Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests