Hello, I have a 88' NG shorty Pajero I'm thinking of moving the rear diff under the leaf springs?
Whats your thoughts?
My thinking would be that the drive shaft would be to short maybe?
Has anyone ever seen or better still done this to their Pajero.
All thoughts welcome.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Diff under leaf springs
Moderator: -Scott-
Hi... it would be an idea if pajo had the same configuration for front and rear axles, like nissan patrol tr, suzuki samurai, toy bj 70/71, etc etc...
The indipendent front axle limits a lot the lift...
I wouldn't go on...
The indipendent front axle limits a lot the lift...
I wouldn't go on...
'96 gen2 2.8 TDI, 33", 4.9 gear ratio,front Arb rear stock locker, Air Flow snorkel, no sway bar
http://www.fondente.org
http://www.youtube.com/fondente71
http://picasaweb.google.com/fondente
http://www.fondente.org
http://www.youtube.com/fondente71
http://picasaweb.google.com/fondente
Its not hard to do I have done a few SPOA (spring pack over axle) on Suzukis .. can be difficult to do right.. You need to be careful to ensure your spring perchs etc are equal and set at the correct angles. Plus you will need to address axle wrap issues (spring pack bending into an S shape .. not good for traction, springs or Universal joints)
If you do go for it and net yourself about a 100mm lift in the rear, what are you going to do about the front ? (a 4 inch\100mm lift in the front IFS is not going to be easy .. or you will need to convert it to a live axle setup as well )
If you do go for it and net yourself about a 100mm lift in the rear, what are you going to do about the front ? (a 4 inch\100mm lift in the front IFS is not going to be easy .. or you will need to convert it to a live axle setup as well )
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
hi i done this one about 1990 on long wb 88 there were several isues drive sharft needs lenthened. but first the springs need to be shortened and also flatterned to make straight other wise the whole arse end sits up to high . also brake cables become a bit short and need re routed over springs. i made my own saddles so lined up pinion better as for performence it had a tendency to lift a rear wheel when doing really hard bits on trips the springs dont flex as much i had an arb locker. fitted it early ninties, so wasnt a problem it did give me a heap more ground clearance i allso lifted transfer case up and cut the gear box crossmember in half long ways and put a flat plate along it this gives you a much better ramp over angle and by adjusting front suspenshion up in the usual ways this truck be come un beatable in its time, it just seamed to go any where i was all ways pulling those early land cruisers out of bogs. any way i hope this helps.
Re: Diff under leaf springs
did you have a go at your spring over , pest here again for got to mention that you can use the complete rear diff housing out of a 94 on model 4x4 delica van including the springs only the hand brake cables are differnt if you use turbo diesel one the diff ratios are 4.875 so the diff will fit as well i fitted one some years back
pest
pest
Who is online
Users browsing this forum: No registered users and 30 guests