Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

getting radius arm bushes out

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
Posts: 613
Joined: Fri Oct 21, 2005 9:33 pm
Location: virginia, brisbane

getting radius arm bushes out

Post by ausoops »

ive bought a full replacement set of bushes for every arm on my 88 shorty. all up cost about $800 for genuine. ive done the panhards no probs but cant get the old metal sleeved bushes in the radius arms out. do i just need to press on the outer sleeve? what can i get that is the same diameter as the outer sleeve to push them out?
swb safari
Top
Posts: 646
Joined: Thu Sep 07, 2006 10:51 pm
Location: Central Coast NSW

b

Post by Clanky »

Should press out ok, but you could grab a hacksaw and put a cut in one side if the ring to relieve the pressure and tap it out with a hammer and punch - you want to be careful not to get crazy with the saw and cut into the radius arm itself
Top
Posts: 765
Joined: Fri Mar 12, 2010 7:28 pm
Location: Fixing something else the kids have broken

Post by BadMav »

Mate, I just drilled into the rubber three times with a 10mm drill to make a sort of slot. Then collapsed the exposed part of the outer ring in towards the centre with a punch. NO risk of hacksawing into the arm then. Worked a treat for me and it was quick.
Don't take life too seriously...it isn't permanent.
Top
Posts: 177
Joined: Mon Sep 28, 2009 10:03 pm
Location: caboolture

Post by anzac »

yeah you just need to get a piece of pipe or something the same diameter and press on the outer metal rim.

I'd suggest obviously that you use a reasonable size press for the job other wise cutting them is pretty much the only way to get them out
Beaut Utes and 4x4's - Driving your dollar further off road

Call Matt - 0411 563 300

[url]beautute.com.au[/url]
lockers, tyres, tube bar work, ute chops
Top
Posts: 709
Joined: Thu Sep 22, 2005 7:49 pm
Location: campbelltown

Post by Mousie »

i baught a 200$ press from a tool shop and got a pice of 50mmx3mm wall round tube and pushed them out in about 10 seconds flat if u have a bit of trouble with your press heat them up with some kind of blowtorch metal expands and they just about fall out
R.A.G, Ruff As Gutts 4x4 club :P
http://www.rag4x4.com/
Top
AJS
Posts: 79
Joined: Sun Mar 20, 2005 10:51 am
Location: Exmouth WA

Post by AJS »

You could use a socket that is a little bit smaller than the bush size to push them out (if you have a press).

The new ones will go in a bit easier if you put them in the freezer for half an hour beforehand.
Top
Posts: 613
Joined: Fri Oct 21, 2005 9:33 pm
Location: virginia, brisbane

Post by ausoops »

i have a press but it would be a massive socket to push out the outer sleeve on the readius arms. i think i will wait till tomorrow when the steel shop re-opens and get a piece of pipe and get it machined down to the correct diameter
swb safari
Top
Posts: 399
Joined: Sat Oct 31, 2009 9:16 pm
Location: Nth Richmond. NSW

Post by Black Bull »

I made a special tool, basically I machined down a big arsed piston Wrist pin down to about 49mm and use that to press through the bush, I can do a full set in about 20 mins
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 123 guests