Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

high or low mount turbo manifold

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Post Reply
Posts: 53
Joined: Fri Dec 01, 2006 11:00 am
Location: Wangaratta, Vic

high or low mount turbo manifold

Post by rustynuts »

Can someone enlighten me on the fors and againsts on a high or low mount manifold for a tubo on a td42. Is there any advantages of either.

Kind regards Rusty
GQ patrol coil cab/chasis tray
Posts: 303
Joined: Wed Nov 24, 2004 8:25 pm
Location: gold coast

Post by mavzilla »

high mount fowls the engine pipe on the aircon pipes, easier to get at the turbo and higher out of the water? low mount lower to the water but wont fry your second battery.
wish list (lockers,lift,endless air,winch,bar,spotties,35s,paint job,turbo,18yrs old hottie
Posts: 765
Joined: Fri Mar 12, 2010 7:28 pm
Location: Fixing something else the kids have broken

Post by BadMav »

High mount: Pros: Easier to plumb, slightly less lag, less chance of thermal shock with water, looks cool :cool:
Cons: More heat / less room in the engine bay and exhaust can be a bit tricky.
Low mount: Pros: Cheap to set up (can use an adapter onto a std manifold), less heat in the engine bay, more room in the engine bay and the exhaust is easier to set up.
Cons: More susceptible to thermal shock with water, slightly more lag and not as cool looking. :cry:
Don't take life too seriously...it isn't permanent.
Posts: 1857
Joined: Fri Feb 02, 2007 12:16 am
Location: ipswich

Post by nastytroll »

I doubt there is any lag difference no a td42 with either manifold. I have fitted Safari, AIT, DTS and standard nissan manifold in low mount and Denco and turboglide highmounts. The runner design would be almost identical aside from which way the collector faces.
Posts: 765
Joined: Fri Mar 12, 2010 7:28 pm
Location: Fixing something else the kids have broken

Post by BadMav »

The lag I speak of is the distance from the compressor side of the turbo to intake manifold, which is negligible, but slightly longer on a low mount. ;)
Don't take life too seriously...it isn't permanent.
Posts: 1857
Joined: Fri Feb 02, 2007 12:16 am
Location: ipswich

Post by nastytroll »

BadMav wrote:The lag I speak of is the distance from the compressor side of the turbo to intake manifold, which is negligible, but slightly longer on a low mount. ;)
So maybe 70mm? But a valid point if not considering intercoolers.

I dounbt that you could find a way to measure the difference aside from calculations which would prove how miniscule it would be.
Posts: 46
Joined: Sun Jan 03, 2010 5:23 pm
Location: ipswich

Post by PIG_GQ »

try a mid mount for somthing diffrent
Posts: 765
Joined: Fri Mar 12, 2010 7:28 pm
Location: Fixing something else the kids have broken

Post by BadMav »

Yeah, you're right it would be absolutely bugger all, like you said minuscule (probably not worth mentioning then ;) ). I only noticed a difference on my 75 series 2h-t when I mounted the 600x 300 front mount on and then there was quite a lull before it boogied but geez, hang on when it did.

Image
Image
Don't take life too seriously...it isn't permanent.
Posts: 4330
Joined: Tue Jun 08, 2004 6:06 pm
Location: Central Victoria

Post by coxy321 »

Low mount: can run top mount IC, and leaves room for all of the other crap in that top-corner, and keeps heat away from the second battery, oil and water plumbing for turbo is a bit shorter.

High mount: direct route to intake manifold (only a fraction shorter than low mount though), can't run top mount IC due to heat and space issues, extra work involved for water/oil/exhaust, extra heat near second battery, air intake (pre-turbo) is easier to rig up compared to low mount.
Posts: 177
Joined: Mon Sep 28, 2009 10:03 pm
Location: caboolture

Post by anzac »

I think what people are saying is that it's much easier and makes more sense to low mount your turbo.

The only real down sides of which are that if you happen to have enough water in the engine bay it'll get wet suddenly, and you can't just pop your bonnet and say to your mates, "look at my fully sic turbo bro." It's slightly less cool to have to point down the side of the motor to show off said turbo.

Save the extra hassle and low mount it. You don't even need to buy a manifold then. You can just fit an adaptor plate to the std one if you're running T28 turbo or other than T3 flanges.
Beaut Utes and 4x4's - Driving your dollar further off road

Call Matt - 0411 563 300

[url]beautute.com.au[/url]
lockers, tyres, tube bar work, ute chops
Posts: 1857
Joined: Fri Feb 02, 2007 12:16 am
Location: ipswich

Post by nastytroll »

there are also more airbox options for running a low mount. You will find it alot harder to fit a top mount airbox with a highmount turbo. Denco use a top mount airbox but the pipe work is very tight on the bend and would be restrictive. So running a highmount only leaves the option of a GU or GQ precleaner airbox if running an AUX battery on the LHS mudgaurd.
Posts: 29
Joined: Fri Apr 24, 2009 6:34 pm
Location: Melbourne

Post by GeeC »

anzac wrote:Save the extra hassle and low mount it. You don't even need to buy a manifold then. You can just fit an adaptor plate to the std one if you're running T28 turbo or other than T3 flanges.
Do you have any further details on using the stock manifold with an adapter?
Posts: 51
Joined: Mon Apr 14, 2008 10:20 pm
Location: wa

Post by Renton »

GeeC wrote:
anzac wrote:Save the extra hassle and low mount it. You don't even need to buy a manifold then. You can just fit an adaptor plate to the std one if you're running T28 turbo or other than T3 flanges.
Do you have any further details on using the stock manifold with an adapter?
+1

Does anyone know if you can buy these adapters off the shelf?
Posts: 2877
Joined: Mon May 10, 2004 9:46 pm
Location: Goodna QLD

Post by ludacris »

You sure can buy the adapters of the shelf.

Cris
Cris's 4 X 4 Accessories & Suspension 0404 736 325 Rock Sliders From $499
Posts: 4330
Joined: Tue Jun 08, 2004 6:06 pm
Location: Central Victoria

Post by coxy321 »

Renton wrote:
GeeC wrote:
anzac wrote:Save the extra hassle and low mount it. You don't even need to buy a manifold then. You can just fit an adaptor plate to the std one if you're running T28 turbo or other than T3 flanges.
Do you have any further details on using the stock manifold with an adapter?
+1

Does anyone know if you can buy these adapters off the shelf?
Any good performance workshop will have them, or you can get them online easy too:
http://cgi.ebay.com.au/T25-T3-Adaptor-F ... 27ad5b61b8

NOTE: Be careful of clearance between your turbo and chassis!
Posts: 51
Joined: Mon Apr 14, 2008 10:20 pm
Location: wa

Post by Renton »

Coxy, Cheers for the link but I was actually refering to the adapter that someone mentioned to go from the standard exhaust manifold to bolt the turbo on.

Cris, As above, is that the same adapter you are refering?
Posts: 4330
Joined: Tue Jun 08, 2004 6:06 pm
Location: Central Victoria

Post by coxy321 »

I can't say i've seen any "adapters" that bolt to a stock manifold (ie. N/A manifold), unless you are talking about a "J" pipe - which i'm fairly sure any reputable workshop would steer well clear of (as its a bit dodgy).

I think anzac needs to clarify which "std" manifold he was referring to (N/A, TD42T etc.).
Posts: 14
Joined: Mon Jul 07, 2008 8:55 pm
Location: s.e melb

Post by banjes »

i give a vote for top mount turbos , as thats all ive had on patrols

they are easy to work on and as everyone has said wont cop all the water!

i have a denco turbo the only problem i see with those is the horrible 90 degree bend dump pipe which seems like it would restrict the exhaust system a little
all in all i like the denco set up

dont cheap out on a turbo kit tho ,spend the little extra to get the best
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Post by toughnut »

No one has mentioned real performance values between the 2 manifolds yet. I'd be really interested to see if there is any. I know when I got mine rebuilt the guy insisted on a high mount turbo. (He normally builds ricer cars). But he never really went into why. It may have been as simple as having space to run the plumbing. Everything was either 3" or 4" piping so it took up a bit of room.
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Posts: 276
Joined: Sat Jul 16, 2005 1:41 pm
Location: Melton, VIC

Post by eighty8 »

coxy321 wrote:I can't say i've seen any "adapters" that bolt to a stock manifold (ie. N/A manifold), unless you are talking about a "J" pipe - which i'm fairly sure any reputable workshop would steer well clear of (as its a bit dodgy).

I think anzac needs to clarify which "std" manifold he was referring to (N/A, TD42T etc.).

Theres reference to 'J' pipe with pics in this thread, http://www.outerlimits4x4.com/ftopic114 ... 2+manifold

I researched manifolds types and adapters a while ago and a 'j' pipe is the only option I found for a standard manifold. Some of the ricers use this as a budget option for there conversions.

cheers.
[url=http://www.patrol4x4.com/forum/showthread.php?t=27334]The Weekend Warrior[/url]
Posts: 1060
Joined: Mon Feb 14, 2005 8:05 pm
Location: Kilsyth, Victoria

Post by hokey »

anyone heard of turbo's blowing up cracking??? when they get in water?
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Post by toughnut »

hokey wrote:anyone heard of turbo's blowing up cracking??? when they get in water?
The only trouble I've had was my factory cast dump pipe broke. :roll:
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests