Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
What so good about the zd30 airbox lid on a td42t?????
What so good about the zd30 airbox lid on a td42t?????
tried searching it, couldnt find any direct answers. all ive heard is the factory 4.2's one is restricting.... does the zd30 one sound any different? does it need to be modified to fit the 4.2's airbox? and what should i expect to pay for one? cheers
99 gu coil cab st, 3 inch zorst, twin subaru turbos on split manifolds 13psi, GTIR intercooler, 4 inch stainless steel snorkel. xgts,35's and 5inch lift and a winch.
If you look down the lid of a td42 (opposite direction to air flow) you will see it squashes down where as the 3L lid is fairly consistent. Much bigger.
I havent done it, but there is a small modification needed to make it fit as there is a MAF senser on the end of the zd lid which makes it a square flange. Shouldnt be hard to knock something up.
No idea on cost, and I wouldnt think it would sound any different.
I havent done it, but there is a small modification needed to make it fit as there is a MAF senser on the end of the zd lid which makes it a square flange. Shouldnt be hard to knock something up.
No idea on cost, and I wouldnt think it would sound any different.
from what ive seen even the second hand lids from the 3L are $2-300.chunks wrote:There is a guy who makes billet lids for them, meant to flow a fiar bit more, but not cheap.
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Goto *
the wreckers only charge $200 for a complete air box, on here ive seen them as cheap as $50, i'm just too slow to get themthehanko wrote:from what ive seen even the second hand lids from the 3L are $2-300.chunks wrote:There is a guy who makes billet lids for them, meant to flow a fiar bit more, but not cheap.
I've bought one from the wreckers aswell, back when I did the turbo conversion. Cost me $150 complete. Bargain. You can't get them anymore for that price..... 
2001 GU Patrol DX wagon, TD42, Air Lockers, twin spare carrier, Barrett HF, 35" Treps, high pinion rear, Staun beadlocks, 60l Engel and more!
The 2.8L airbox is similar but not exactly the same as the 3.0L. I bought a 3.0L lid for my 2.8L airbox. I had to grind a tab/bracket of the 2.8L airbox so that the 3.0L lid would fit. This is not a big deal and took about 30 seconds with the grinder.satman wrote:is the 2.8 air box the same as the 3L ???
The outlet is on the lid. I cant comment about the outlet positioning between the two lids as I haven't looked. Note that the flange and bolt pattern to attach the airflow meter to the end of the outlet is different between the 2.8L and 3.0L lids. Most people I have seen that have used a 3.0L lid on a 2.8L or 4.2L airbox have cut the airflow meter flange off the end of the lid, leaving a 3 inch pipe. This can be used to clamp a silicon hose too, for custom turbo/inlet piping.
Who is online
Users browsing this forum: No registered users and 147 guests