Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

TD42T with eletric injector pump. witch wires make it go

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
Posts: 38
Joined: Mon Aug 30, 2004 3:27 pm
Location: sunshine coast

TD42T with eletric injector pump. witch wires make it go

Post by extra niss »

hay everyone
i just got a GU witch is half converted to a TD42T ( the very later modal one factory intercooled) and it has 3 wires coming out if the pump and 2 wires going into a solenoid or senser in the bottom of the pump.
i have been told i need to put power to 2 of the wires to make it go. but i have no idea witch 2 wires. anyone dune it before or can help me out
Top
Posts: 1258
Joined: Wed Mar 21, 2007 7:49 pm
Location: Mornington/ Victoria

Contact:
Contact PGS 4WD

Post by PGS 4WD »

That is the immobilizer model pump. I cant' remember which wire, it's one of the three. If there is a red one that rings a bell?? Sorry thats all I can recall.


joel
-Pre trip inspections/ servicing
-Suspension/ custom modifications
-4wd Dyno & tuning
-Qualified mechanics
Top
Posts: 38
Joined: Mon Aug 30, 2004 3:27 pm
Location: sunshine coast

Post by extra niss »

thanks heeps mate that gives me some where to start
Top
Posts: 748
Joined: Tue Nov 09, 2004 9:45 pm
Location: Lilydale

Contact:
Contact Dzltec

Post by Dzltec »

You will need to remove the immobilizer unit. It receives a signal from a main control unit to make it start. If you have all the modules and wiring then all should be ok if connected correctly.


Andy
www.diesel-tec.com.au Ph 03 9739 5031
Ball bearing turbo upgrades for factory turbo vehicles. Got a diesel question just ask.
Home of the twin turbo shorty and many 150rwkw+ patrols.
Top
Posts: 38
Joined: Mon Aug 30, 2004 3:27 pm
Location: sunshine coast

Post by extra niss »

Dzltec wrote:You will need to remove the immobilizer unit. It receives a signal from a main control unit to make it start. If you have all the modules and wiring then all should be ok if connected correctly.


Andy
i havn't got the computers and wiring for the immobilizer is there any way around it or have i got to change the pump or part of the pump
Top
Posts: 175
Joined: Tue Feb 23, 2010 4:49 pm
Location: Dyno

Post by UGOTNUFN »

extra niss wrote:
Dzltec wrote:You will need to remove the immobilizer unit. It receives a signal from a main control unit to make it start. If you have all the modules and wiring then all should be ok if connected correctly.


Andy
i havn't got the computers and wiring for the immobilizer is there any way around it or have i got to change the pump or part of the pump
You will also need to power up the TCV (Timing Control Valve) at the bottom of the pump,normally a boost sensitive switch is the best way to switch it on and off.
Top
Posts: 748
Joined: Tue Nov 09, 2004 9:45 pm
Location: Lilydale

Contact:
Contact Dzltec

Post by Dzltec »

The immobilser can be removed, however it is difficult to do as the use sheer bolts to locate it. Having a timing control valve throws a spanner in the works as it will make the pump have full advance at all times. It usually recieves a duty cycle controoled voltage to control the opening time which controls how much injection advance you have. This can be changed to a mechanical system but involves changing the main housing.


Andy
www.diesel-tec.com.au Ph 03 9739 5031
Ball bearing turbo upgrades for factory turbo vehicles. Got a diesel question just ask.
Home of the twin turbo shorty and many 150rwkw+ patrols.
Top
User avatar
sw1
Posts: 297
Joined: Mon Mar 15, 2004 10:06 am
Location: around the place

Post by sw1 »

UGOTNUFN wrote: You will also need to power up the TCV (Timing Control Valve) at the bottom of the pump,normally a boost sensitive switch is the best way to switch it on and off.
??

its pulse width modulated, a on off switch isnt going to do much here.
2003 GU Patrol ST 4.2L Diesel Turbo Intercooled
1988 D21 Pathfinder 3.8L V6 & T700 - SOLD 11/12
Top
Posts: 782
Joined: Tue Mar 08, 2005 12:03 pm
Location: brisbane

Post by giantracing »

put a hoob switch in the cooler to turn on and off using boost pressure, it makes a big difference when driving..... but with out using it , it will still start... we modify these on late model gu's...
build em tuff, drive em ruff.........

Custom 4wd Creations Brisbane
0438279890
Top
Posts: 175
Joined: Tue Feb 23, 2010 4:49 pm
Location: Dyno

Post by UGOTNUFN »

sw1 wrote:
UGOTNUFN wrote: You will also need to power up the TCV (Timing Control Valve) at the bottom of the pump,normally a boost sensitive switch is the best way to switch it on and off.
??

its pulse width modulated, a on off switch isnt going to do much here.
On and off with a Hobbs switch set to 3Psi is fine
Top
Posts: 38
Joined: Mon Aug 30, 2004 3:27 pm
Location: sunshine coast

Post by extra niss »

ok thanks heaps everyone that has been a big help
Top
Posts: 1258
Joined: Wed Mar 21, 2007 7:49 pm
Location: Mornington/ Victoria

Contact:
Contact PGS 4WD

Post by PGS 4WD »

I got one going that had failed in the immobilizer just with a voltage at one of those three wires, possible because the unit was faulty. It's worth a try.

Joel
-Pre trip inspections/ servicing
-Suspension/ custom modifications
-4wd Dyno & tuning
-Qualified mechanics
Top
Posts: 38
Joined: Mon Aug 30, 2004 3:27 pm
Location: sunshine coast

Post by extra niss »

i drilled the illommobiliser off yesterday and exposesed the fuel cut solenoid. to ezy :) somthing went right for a change
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 2 guests