Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
best place to fit airlocker in bris
best place to fit airlocker in bris
I have a new RD70 air locker which needs to be installed, i have a new bearing kit including pinion bearings that i want used insted of the originals as they are many km's old and a bit sad. where in bris wold be the best & cheapest to fit this all to my ute or does anyone know how to do it properly that wants to do a cash job for me?
An ounce of precaution is better than a ton of cure!
dont knot if allowed to mention names but the lard 3 lettered company that sells and fitts air lockers and advertises them that starts with A.. Rooted mine and damaged my dashboard when installing the wiring ( even after i told them not ot do wiring as i dont rust anyone doing it, im an electrician) they opened my dash with a screw driver and practically accused me of bullshiting them when i noticed it. ( 30,000 klm old truck) took lot of stuffing around and pone calls to get it all sorted.
i then did my rear myself, not very hard, they give u instructions, i dowloaded the nissan workshop manual ( nissan one) as i bought a max elleries workshop manual and found it very basic on information and also incorrect on some information. ( torque settings were stated in distances was quiet hilarious)
once i had the correct info from teh nissan manual its all easy.
u will need a dial indicator, torque wrench that can read as low as 2 nm and one that will read between 150 and 200 nm. and a good vice. mine took me about 4 hours and bout half a carton.
failing that when u do it urself if u stuff the air line tuve i.e kink it ( copper) apparently there like 180$ and also if u get a oil leak or failure u have to pull it out and fix urself. my mate paid Mobi Diffs at aranda street in slacks creek to do his fronts and backs ( and he's a fitter by trade) just he's lazy. think it was abotu 300 per diff to fit and install. but dont quote me on those prices.
that was including replacing his pinion bearings and shims etc.
have used him for gearbox rebuilds in fourbies and race cars and is very good from my experiences.
Mobi Diffs
11 Aranda St, Slacks Creek QLD 4127
ph: 0413 072 075
personally for the $ ide pay them to do it as if u dont have the equipment u will spend about 300 on average tools ( torque wrench's) to do and they give warranty.
i then did my rear myself, not very hard, they give u instructions, i dowloaded the nissan workshop manual ( nissan one) as i bought a max elleries workshop manual and found it very basic on information and also incorrect on some information. ( torque settings were stated in distances was quiet hilarious)
once i had the correct info from teh nissan manual its all easy.
u will need a dial indicator, torque wrench that can read as low as 2 nm and one that will read between 150 and 200 nm. and a good vice. mine took me about 4 hours and bout half a carton.
failing that when u do it urself if u stuff the air line tuve i.e kink it ( copper) apparently there like 180$ and also if u get a oil leak or failure u have to pull it out and fix urself. my mate paid Mobi Diffs at aranda street in slacks creek to do his fronts and backs ( and he's a fitter by trade) just he's lazy. think it was abotu 300 per diff to fit and install. but dont quote me on those prices.
that was including replacing his pinion bearings and shims etc.
have used him for gearbox rebuilds in fourbies and race cars and is very good from my experiences.
Mobi Diffs
11 Aranda St, Slacks Creek QLD 4127
ph: 0413 072 075
personally for the $ ide pay them to do it as if u dont have the equipment u will spend about 300 on average tools ( torque wrench's) to do and they give warranty.
06 GU Coil cab, 4 inch lift, drop arms, custom shock mounts rear, twin locked, 35 creepy's,
it'd be a bit of a drive but moreton automotive in nerangba (20mins north of brisbane) does a top job and he's pretty cheap. No worries rebuilding your diff at the same time.
Give lee a call on 07 3888 0119.
Give lee a call on 07 3888 0119.
Beaut Utes and 4x4's - Driving your dollar further off road
Call Matt - 0411 563 300
[url]beautute.com.au[/url]
lockers, tyres, tube bar work, ute chops
Call Matt - 0411 563 300
[url]beautute.com.au[/url]
lockers, tyres, tube bar work, ute chops
Who is online
Users browsing this forum: No registered users and 19 guests