hi
is it actually possible to change air conditioning compressor to air compressor to inflate my tires. if yeas what it takes.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
air condition to air compressor
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Yes, it is possible, but it's not always very successful. It depends on what type of pump you have.
Vane compressors are now the most common and they don't convert well.
Axial piston compressors convert quite successfully (Sanden are the most common) but will still need to be oiled. I believe "endless air" compressors are Sanden pumps with different seal material and a grease nipple fitted in place of running oil in the supply air.
York piston compressors are the best option - they require no modifications and will deliver 9 cfm @ 3000rpm for years and years.
If you have a vane compressor, I wouldn't bother trying to convert it. It will have a short, oily, messy life.
Steve.
Vane compressors are now the most common and they don't convert well.
Axial piston compressors convert quite successfully (Sanden are the most common) but will still need to be oiled. I believe "endless air" compressors are Sanden pumps with different seal material and a grease nipple fitted in place of running oil in the supply air.
York piston compressors are the best option - they require no modifications and will deliver 9 cfm @ 3000rpm for years and years.
If you have a vane compressor, I wouldn't bother trying to convert it. It will have a short, oily, messy life.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Sorry, oyamum, but how has this helped? tufftruckin & myself have provided some specific information. I have run a York piston A/C compressor for years as an air compressor. I also tried running a Denso vane style compressor for pumping tyres. I set it up with an oiler on the intake side. After very little use it became so slow and hot it was pointless.
You'll need to provice some actual information about which pumps modified in which way to add to this thread.
And in any case, what does "not as efficient as dedicated properly designed air compressor" mean? Most dedicated properly designed air compressors deliver less than 2cfm at 100% duty cycle. Just how efficient are these converted pumps you are talking about?
Steve.
You'll need to provice some actual information about which pumps modified in which way to add to this thread.
And in any case, what does "not as efficient as dedicated properly designed air compressor" mean? Most dedicated properly designed air compressors deliver less than 2cfm at 100% duty cycle. Just how efficient are these converted pumps you are talking about?
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
I'm using a sanden SD510. with the sandens you need to pull the head off and modify the valve plate to stop the grease u put in it to lubricate for entering your air lines , tank , locker ect
It is a simple process that anyone with basic tools can do. you will need to but a 1/8 UNF grease nipple! they are hard to find as most grease nipples come in NPT & BSP.
here is a link to a write up someone has done on doing the mod to the valve plate!
http://www.grungle.com/endlessair.html
It is a simple process that anyone with basic tools can do. you will need to but a 1/8 UNF grease nipple! they are hard to find as most grease nipples come in NPT & BSP.
here is a link to a write up someone has done on doing the mod to the valve plate!
http://www.grungle.com/endlessair.html
An ounce of precaution is better than a ton of cure!
tufftruckin wrote:I'm using a sanden SD510. with the sandens you need to pull the head off and modify the valve plate to stop the grease u put in it to lubricate for entering your air lines , tank , locker ect
It is a simple process that anyone with basic tools can do. you will need to but a 1/8 UNF grease nipple! they are hard to find as most grease nipples come in NPT & BSP.
here is a link to a write up someone has done on doing the mod to the valve plate!
http://www.grungle.com/endlessair.html
Sorry tufftruckin that sight for me comes up as a forbiden sight?! is that me or is it the link?
Cheers, Dave
loose as a goose
No matter how tempting a vane compressor may appear ( i.e. its available as an OE fit.... ) i'd suggest your not going to be happy.
During normal operation they pass significant quantities of oil through the compressor to provide tip sealing and lubrication. Normally they use a small bypass internally to circulate some lubricant directly but the rest just circulates through the AC system. As the system is closed nothing gets lost.
However for non AC uses if you put enough oil through them to seal / lubricate successfully then your going to end up with heaps of oil in your receiver/tyres ( in fact everywhere... ). I also tried a separate oil separator and pressure return back to the suction. It was a nightmare to try and get the circulation right and it also varied depending on engine speed.
Ended up a complex system that didn't work - would carbonize the oil at low feedback rate and waste air at higher settings. I hate electric compressors - but compared with my vane installation they are perfect, and that's saying something.
I haven't seen a screw type used but from my understanding they also rely on oil for tip sealing, so i'd bet against them.
Traditional or axial piston systems seem to be by far the most sucessful.
During normal operation they pass significant quantities of oil through the compressor to provide tip sealing and lubrication. Normally they use a small bypass internally to circulate some lubricant directly but the rest just circulates through the AC system. As the system is closed nothing gets lost.
However for non AC uses if you put enough oil through them to seal / lubricate successfully then your going to end up with heaps of oil in your receiver/tyres ( in fact everywhere... ). I also tried a separate oil separator and pressure return back to the suction. It was a nightmare to try and get the circulation right and it also varied depending on engine speed.
Ended up a complex system that didn't work - would carbonize the oil at low feedback rate and waste air at higher settings. I hate electric compressors - but compared with my vane installation they are perfect, and that's saying something.
I haven't seen a screw type used but from my understanding they also rely on oil for tip sealing, so i'd bet against them.
Traditional or axial piston systems seem to be by far the most sucessful.
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
Road Ranger
given that screw type compressors are used in high flow air compressors in industrial applcations they may actually be a good optionMightyMouse wrote:
I haven't seen a screw type used but from my understanding they also rely on oil for tip sealing, so i'd bet against them.
If the above post did not offend you in any way please PM me so I can try harder!!
Yes i see your point, but the ones we are looking at are AC units where recovering the oil is a given.
Screw Air compressors don't have that luxury so i'm guessing they put far more effort into tip sealing / oil recovery.
Whilst the principal is the same... the application is different so ......
Screw Air compressors don't have that luxury so i'm guessing they put far more effort into tip sealing / oil recovery.
Whilst the principal is the same... the application is different so ......
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
.
I have a gq patrol and converted my standard ac pump into an air compressor over 6 years ago with no problems to date.
I disconnected the inlet and put a filter on it and plumbed the outlet into a tank. Every time I give the car a good wash (every 2-3 months) i squirt some air oil in the inlet.
I still can use a rattle gun and pump 4 tires up in the time my mates do 2.
I disconnected the inlet and put a filter on it and plumbed the outlet into a tank. Every time I give the car a good wash (every 2-3 months) i squirt some air oil in the inlet.
I still can use a rattle gun and pump 4 tires up in the time my mates do 2.
WHEELERS FABRICATIONS, DUEL CAB + EXO CAGE. 4"SUSP 2"BODY 35" CLAWS, TWIN LOCKED, BUILT 4 FUN
IMHO if you have the room definately get the york. They can be fairly readily found in 80's volvos, v8 fords & valiants amoungst others.
But be aware there are 3 different models relating to the capcity 206, 209 & 210.
Some great info here - http://www.jedi.com/obiwan/jeep/yorkair.html
My TJ ran the 210 and was everything I nedded, including powering the AirBag Suspension.
But be aware there are 3 different models relating to the capcity 206, 209 & 210.
Some great info here - http://www.jedi.com/obiwan/jeep/yorkair.html
My TJ ran the 210 and was everything I nedded, including powering the AirBag Suspension.
Cheers [url=http://www.wooders.com.au]Wooders[/url]
Who is online
Users browsing this forum: No registered users and 6 guests