Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Mq Owners Need Measurement

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Mq Owners Need Measurement

Post by A1 »

As stated im chasin the measurement wen steering is turned full left or full right on the left hand side (tierod/draglink TRE )

On the back side where the draglink TRE is to the front of the axle housin ................


The reason i need the measurement is because im gunna fit my Mq knuckles soon and i need to know if this will clear the front of the radius arm on the left hand side



Dan
[b][i] DAN [/i] [/b]


:silly:
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

in other words you want to know tha gap between the draglink and the axle tube at full lock .... correct ??? :D
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

V8Patrol wrote:in other words you want to know tha gap between the draglink and the axle tube at full lock .... correct ??? :D


clearance between tie-rod and axle housing. and the diemeter of the axle tube and the diameter of the tie rod would be good to make sure he is comparing against the right measurements.

reason being I don't think anyone has done the MQ knuckle thing on a vehicle still wearing radius arms so far??

he is gonna have to worry about wether the ball joint stud is gonna foul on the radius arm as well. but we'll get to that later :?
I am thinking it will be towards the outside of the arm the whole time :?:
Top
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Post by A1 »

Wendle wrote:
V8Patrol wrote:in other words you want to know tha gap between the draglink and the axle tube at full lock .... correct ??? :D


clearance between tie-rod and axle housing. and the diemeter of the axle tube and the diameter of the tie rod would be good to make sure he is comparing against the right measurements.

reason being I don't think anyone has done the MQ knuckle thing on a vehicle still wearing radius arms so far??

he is gonna have to worry about wether the ball joint stud is gonna foul on the radius arm as well. but we'll get to that later :?
I am thinking it will be towards the outside of the arm the whole time :?:


Thanx Carlton


Lucky some1 could explain in clearer terms the distances i need :oops:



Dan
[b][i] DAN [/i] [/b]


:silly:
Top
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Post by A1 »

If no wants to help out .................... :roll:



Then Wendle any chance of you doin a check on ya beasty like full lok and measure from back side of the TRE to the housin and then measure the width of the MQ tre and the standard gq tre end and minus that off the other measurement :roll: my Drag link will be the same od as yours as im sure you are aware ...........( should of checked this on yours on the weekend :idea: im fukin stoopid :armsup:



is that right :oops:



Dan
[b][i] DAN [/i] [/b]


:silly:
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

yeah, no worries. I was out there last night too.. :cry:
should be out there again tomorrow night..
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

A1MAV wrote:If no wants to help out .................... :roll:


Opps....sorry mate forgot all about this :oops:

I'll get the tape out this arvo 4 ya :D

Might even get some pics 2 :D :D
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Post by A1 »

Thanx Mate


Piccys would also beat farken awesome if ya can ...............


Ive had a dramas just happen so there aint no real rush now although the sooner i know the sooner i guess i can get the shite ready and on





Cheers Dan
[b][i] DAN [/i] [/b]


:silly:
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

pics....


the draglink only gets as close as 92mm on both left & right full lock.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Post by A1 »

Cheers V8patrol by the looks of your front housin axle tubes they seem to be less than 100mm??? .....this is also critical for me cause the gq 's are bout 100mm and this will degrease the 92mm measurement ..........

I will check tonight and c how far out the radius arms protrude from the housin but thinkin bout it may sit above the highest point on the radius arm bracket.......


thanx again Dan :D
[b][i] DAN [/i] [/b]


:silly:
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

yeah the front tubes are around the 90mm diameter mark., the rears on the MQ are 100mm !!

Your only loosing 8mm, whats the worry there ???
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

V8Patrol wrote:Your only loosing 8mm, whats the worry there ???


he has a fawking big radius arm hanging out the front in that general area!
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

Wendle wrote:
V8Patrol wrote:Your only loosing 8mm, whats the worry there ???


he has a fawking big radius arm hanging out the front in that general area!


got a grinder and welder?????


Modify it or Move it !!, after all its only a "
fawking big radius arm
:rofl:
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

V8Patrol wrote:
Wendle wrote:
V8Patrol wrote:Your only loosing 8mm, whats the worry there ???


he has a fawking big radius arm hanging out the front in that general area!


got a grinder and welder?????


Modify it or Move it !!, after all its only a "
fawking big radius arm
:rofl:


its taken him 2 years to build some bumper bars and a couple of shock mounts! he has no time left to modify radius arms before they outlaw the internal combustion engine!! :finger:
Top
Posts: 15549
Joined: Tue Oct 22, 2002 9:23 am
Location: Your Mummas House!

Contact:
Contact bj on roids

Post by bj on roids »

Wendle wrote:
V8Patrol wrote:
Wendle wrote:
V8Patrol wrote:Your only loosing 8mm, whats the worry there ???


he has a fawking big radius arm hanging out the front in that general area!


got a grinder and welder?????


Modify it or Move it !!, after all its only a "
fawking big radius arm
:rofl:


its taken him 2 years to build some bumper bars and a couple of shock mounts! he has no time left to modify radius arms before they outlaw the internal combustion engine!! :finger:


ROFLMAO!! Yes he seems pretty slack, that hypo on the other hand seems to get a lot done, maybe he should take a page out of bens book? :armsup:
hands and mums dont count!!!
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

bj on roids wrote:
Wendle wrote:
V8Patrol wrote:
Wendle wrote:
V8Patrol wrote:Your only loosing 8mm, whats the worry there ???


he has a fawking big radius arm hanging out the front in that general area!


got a grinder and welder?????


Modify it or Move it !!, after all its only a "
fawking big radius arm
:rofl:


its taken him 2 years to build some bumper bars and a couple of shock mounts! he has no time left to modify radius arms before they outlaw the internal combustion engine!! :finger:


ROFLMAO!! Yes he seems pretty slack, that hypo on the other hand seems to get a lot done, maybe he should take a page out of bens book? :armsup:


ROFL PCOC that is hilarious on so many levels, say hello to shirls for me! :armsup:
Top
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Post by A1 »

Wendle wrote:
V8Patrol wrote:
Wendle wrote:
V8Patrol wrote:Your only loosing 8mm, whats the worry there ???


he has a fawking big radius arm hanging out the front in that general area!


got a grinder and welder?????


Modify it or Move it !!, after all its only a "
fawking big radius arm
:rofl:


its taken him 2 years to build some bumper bars and a couple of shock mounts! he has no time left to modify radius arms before they outlaw the internal combustion engine!! :finger:



hahahahaha well some1 was comin up to give me ahand but he backed out :roll:




How are those match sticks goin Wendle :lol:


:armsup: A1 takin it slow n steady
[b][i] DAN [/i] [/b]


:silly:
Top
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Post by A1 »

bj on roids wrote:
Wendle wrote:
V8Patrol wrote:
Wendle wrote:
V8Patrol wrote:Your only loosing 8mm, whats the worry there ???


he has a fawking big radius arm hanging out the front in that general area!


got a grinder and welder?????


Modify it or Move it !!, after all its only a "
fawking big radius arm
:rofl:


its taken him 2 years to build some bumper bars and a couple of shock mounts! he has no time left to modify radius arms before they outlaw the internal combustion engine!! :finger:


ROFLMAO!! Yes he seems pretty slack, that hypo on the other hand seems to get a lot done, maybe he should take a page out of bens book? :armsup:



So wat ya sayin BJ is that wen he ask's me for a hand i should do wat he duz to me n say gee sorry dude im half cut ya should of rang earlier :drinking: ......................................
[b][i] DAN [/i] [/b]


:silly:
Top
User avatar
A1
Posts: 3451
Joined: Tue Jan 28, 2003 8:57 pm
Location: NEWCASTLE

Post by A1 »

Hey wendle ya had a chance to measure ya front end for us yet




:D A1
[b][i] DAN [/i] [/b]


:silly:
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

i tried to come up and give you a hand, but you are a friggin workaholic!

I'll be out there tomorrow night I'll compare it to my other truck and let you know if it will fit. should have done this in the first place, I guess! :cool:
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

A1MAV wrote:How are those match sticks goin Wendle :lol:



bahahahahhah ROFL. it's taken me all day to realise what you were talking about! fark that was funny!
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 2 guests