Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Timing chain replacement, type ? info ?

Tech Talk for Rover owners.

Moderator: Micka

Post Reply
Posts: 142
Joined: Mon Nov 10, 2003 6:36 pm
Location: Vic

Timing chain replacement, type ? info ?

Post by Rovernaut »

I've done 190K on my 3.9 EFI.V8i
I believe that is advisable to change the timing chain on high milage engines.
Question: Should I replace it with a genuine chain and also replace the camshaft and crankshaft gears with the same. OR/ Go for an after market timing set?
I was at a spars supplier the other day and was advised that I would have to buy a new kit as there was a problem with OEM timing chains rubbing the timing casing, causing it to wear a hole in it. And this $450 'kit' remedied it.
I'm a little confused, My OEM has been fine till now.
I also have heard there are Duplex timing chains avail.
Any one replaced theirs recently and can give me some info.
Posts: 56
Joined: Wed Jan 21, 2004 9:09 pm
Location: Melbourne

Post by RobG65 »

I replaced mine when I did my cam, with a Rollmaster roller timing chain set. I doubt the OEM will ever rub on the timing case. However I can tell you the duplex will. What I did was bolt the timing case back lightly after installing the cam & timing set, and rotated the motor so I could see where it was going to rub, then using an angle grinder removed enough material so that it wasnt going to be a problem any more. Easy to do, just easy does it with the angle grinder, wouldnt want to break though the other side :lol: .

Regards
RobG65
"All the parts falling off this truck are of the very finest British manufacture"
Posts: 142
Joined: Mon Nov 10, 2003 6:36 pm
Location: Vic

Post by Rovernaut »

RobG65, since you had to remove some metal on the timing cover , if the roller master chain stretches won't it then cut through??? :?:
Posts: 56
Joined: Wed Jan 21, 2004 9:09 pm
Location: Melbourne

Post by RobG65 »

Being Duplex chain it shouldnt stretch as quickly as the OEM. The area that needed to be cleared was around the camshaft sprocket area. The chain being guided by the sprocket should keep it away from the area already ground. If I remember correctly on the installation desructions it was mentioned some metal removal might be required from the timing case.

By the time this is a concern for me Im hoping I will given the 3.9 the heave ho and replaced it with a holden 5Ltr efi motor.

Regards
RobG65
"All the parts falling off this truck are of the very finest British manufacture"
Posts: 56
Joined: Wed Jan 21, 2004 9:09 pm
Location: Melbourne

Post by RobG65 »

Being Duplex chain it shouldnt stretch as quickly as the OEM. The area that needed to be cleared was around the camshaft sprocket area. The chain being guided by the sprocket should keep it away from the area already ground. If I remember correctly on the installation desructions it was mentioned some metal removal might be required from the timing case.

By the time this is a concern for me Im hoping I will given the 3.9 the heave ho and replaced it with a holden 5Ltr efi motor.

Regards
RobG65
"All the parts falling off this truck are of the very finest British manufacture"
Posts: 142
Joined: Mon Nov 10, 2003 6:36 pm
Location: Vic

Post by Rovernaut »

Thanks RobG65, What was the cost/ and where did you source it if you don't mind me asking. :)
Posts: 56
Joined: Wed Jan 21, 2004 9:09 pm
Location: Melbourne

Post by RobG65 »

I got mine from Les Richmond Automotive, was around $160 for the Rollmaster set, you might find it cheaper? Dont forget do get a timing case gasket and the oil seal for the crankshaft pulley in the timing case. If your lucky you can remove the timing case without stuffing the sump gasket by undoing the four front bolt from thh sump and gently removing the timing case. However for the sake of $8-10 grab a sump gasket anyway. I wasnt lucky and had to remove the sump.

Grinz only Rover I havent seen leak oil all over the drive way now.....and yes I have oil in it :lol:
"All the parts falling off this truck are of the very finest British manufacture"
Posts: 82
Joined: Wed Sep 10, 2003 4:14 pm
Location: Sydney

timimg

Post by Rangee »

i have a brand new timing chain and sprockets .. it you want it ... $120 for both
cheers
Rangee
Virgins !!!
someone has to go first !
Posts: 142
Joined: Mon Nov 10, 2003 6:36 pm
Location: Vic

Post by Rovernaut »

RobG65 wrote:I got mine from Les Richmond Automotive, was around $160 for the Rollmaster set, you might find it cheaper? Dont forget do get a timing case gasket and the oil seal for the crankshaft pulley in the timing case. If your lucky you can remove the timing case without stuffing the sump gasket by undoing the four front bolt from thh sump and gently removing the timing case. However for the sake of $8-10 grab a sump gasket anyway. I wasnt lucky and had to remove the sump.

Grinz only Rover I havent seen leak oil all over the drive way now.....and yes I have oil in it :lol:

Thanks for the advice. Mine doesn't use a sump gasket. It is a later model 3.9l that requires RTV gasket silicon only.
From What I've read, I just need to apply RTV to the front of the sump atrea. It it leaks I dio the sump again. It's pretty easy fix.
How did you get the Viscous fan off. I'm thinking of fabricating a "spanner " with the 36mm opening I think it is my self. I dont have a shifter that opens wide enough.
Posts: 56
Joined: Wed Jan 21, 2004 9:09 pm
Location: Melbourne

Post by RobG65 »

I have a shifter with a large enough opening. There are four bolts holding the pulley on to the water pump. I used a large screw driver as a lever between the hub on the pully and one of the bolts and the shifter on the nut.

Cheers
RobG65
"All the parts falling off this truck are of the very finest British manufacture"
Posts: 142
Joined: Mon Nov 10, 2003 6:36 pm
Location: Vic

Post by Rovernaut »

Thanks for the advise gentlemen ;)
Posts: 56
Joined: Wed Jan 21, 2004 9:09 pm
Location: Melbourne

Post by RobG65 »

Rovernaut wrote:Thanks for the advise gentlemen ;)


Ummmm one thing!...the thread is left handed. So looking from the front of the motor when undoing the nut, turn the spanner clockwise.

RobG65
"All the parts falling off this truck are of the very finest British manufacture"
Posts: 142
Joined: Mon Nov 10, 2003 6:36 pm
Location: Vic

Post by Rovernaut »

RobG65 wrote:
Rovernaut wrote:Thanks for the advise gentlemen ;)


Ummmm one thing!...the thread is left handed. So looking from the front of the motor when undoing the nut, turn the spanner clockwise.

RobG65

That would make sense, otherwise it would undo it self in rotation.

Suits me fine as I'm a lefthander too :D LOL
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests