need some thing that works to copy from
and a novel on how to do it would be nice 8)
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
lifting a bull bar with the body lift .....
lifting a bull bar with the body lift .....
Has any one got any photos of a lifted bullbar?
need some thing that works to copy from
and a novel on how to do it would be nice 8)
need some thing that works to copy from
and a novel on how to do it would be nice 8)
tjm bar was easy, just cut flat bar that goes inside chassis rails, weld it back on 2" lower then weld some angle beside original mount [make sure it clears bolt holes] and add infill flat to make it look pretty.
it was way stronger than original.
sold truck so no pics.
it was way stronger than original.
sold truck so no pics.
[url=http://bigred.redbubble.com/][color=red][b]You can follow me but its gunna hurt ![/b][/color][/url]
event pics http://bigred.redbubble.com/
event pics http://bigred.redbubble.com/
big red wrote:tjm bar was easy, just cut flat bar that goes inside chassis rails, weld it back on 2" lower then weld some angle beside original mount [make sure it clears bolt holes] and add infill flat to make it look pretty.
it was way stronger than original.
sold truck so no pics.
That is exactly how my ARB bar is done for a 2inch body lift. Looks like nothing has been modified.
MY JEEP BUILD
v840 wrote: [Not a shot at Tonka] It's like saying, hell I've got two nuts, I may as well cut one of them off for the hell of it. I ain't using it.[/NAS@T] It's ridiculous!
On the topic of body lifts and bBars, if people have pictures of any bar work on GQ's would they be able to email them to me. As I am getting a custom bar made to suit my body lift and PTO winch, either next week or the one after and I need some more ideas.
email - turps@myplace.net.au
Turps
email - turps@myplace.net.au
Turps
Hey Terrafirma
Just had this done for me, as I was two lazy to do it myself :wink:
The pictures aren't real flash, but its basically just had the chassis sleeve cut off and lowered two inches with extra plates and gussets welded in.
I'll try and get some better pic's before I remount it.
I'm getting the bar sandblasted, zinced and powdercoated after putting some extra braces behind it, worth more than the bar itself !
Just had this done for me, as I was two lazy to do it myself :wink:
The pictures aren't real flash, but its basically just had the chassis sleeve cut off and lowered two inches with extra plates and gussets welded in.
I'll try and get some better pic's before I remount it.
I'm getting the bar sandblasted, zinced and powdercoated after putting some extra braces behind it, worth more than the bar itself !
[quote="barnsey"]smoked Elle McPherson, even though I didn't inhale[/quote]
[url=http://www.outerlimits4x4.com/PHP_Modules/phpBB2/viewtopic.php?p=765579&highlight=#765579/]Roadrunners Hilux[/url]
[url=http://www.outerlimits4x4.com/PHP_Modules/phpBB2/viewtopic.php?p=765579&highlight=#765579/]Roadrunners Hilux[/url]
Posts: 3825
Joined: Wed Nov 06, 2002 8:42 pm
Joined: Wed Nov 06, 2002 8:42 pm
Location: in the sky , its a bird , its a plane ! No its super MOOSE !!!
we do !!
wat we do is move the chassis !!!
just in front of the round cross member, cut the chassis off , add plate (use 6 or 8 mm) re-position previously cut off sections to reguired hight & weld & gussett !!!!
that way if you ever want to change bars , for wat eva reason , u dont have to re-modify another bar !!!!!
& we get it engineered !!!!!
just in front of the round cross member, cut the chassis off , add plate (use 6 or 8 mm) re-position previously cut off sections to reguired hight & weld & gussett !!!!
that way if you ever want to change bars , for wat eva reason , u dont have to re-modify another bar !!!!!
& we get it engineered !!!!!
MissForbyNoob wrote:
and one day i'll just become a worthless housewife.
and one day i'll just become a worthless housewife.
How to Body Lift.
35 to 40mm is a sensible lift.
I just prefer Ally but steel is ok. I havnt used nylon. If its hard it should be ok. Run a 12 to 13 mm hole thru the middle.
The mounts are 70mm. So min is this size . 80 is better. Under door mounts will need a slight chamfer on inner top edge if using larger than 72 as floor mount curves slightly. Check when fitting.
Bolts should be proportionately shorter than listed below. Rear two need to be longer by about 25/30,mm to allow for captive nut size.
Remove carpets, seatbelt bottom bolts.Bottom clip on plastic bit on fan cowling.
Undo all bottom nuts and two rear bolts. (use heat inside floor to break the loctite ion these two) You can drill these captive nuts out to allow the use of longer thru bolts from the top the same as all the others.
I sometimes have had to cut floor here with tin snips to get to nuts, then just screw an ally plate over hole.
Jack up truck body with bits of wood on trolley jacks front and rear until body comes clear of mounts. Check every where for binding., fuel hoses etc.
Keep lifting until new spacers can be slid in, using a bit of grease to reduce corrosion later, take care of fingers.
When istalling a body lift check the following:
1. Steering slip joint to shaft, slide down a bit to relieve stress
2. Brake coiled pipe between body and chassis (under master cyl) open them up
3. Cable loom (under passenger seat) to chassis
4. Clutch flexible pipe from gearbox to body, bend down body bracket
5. Remove small shroud extension from bottom of radiator.
6. Replace fuel feed and return hoses, body to fuel pump, with longer ones - esp on diesel.
7. Check air con hoses from pump up to body isnt snagging.
8. Low range lever will need mod to it and surrounding area, more so on GQ1s.
9. Gearlever aperture likewise for 2nd, 4th and rev.
10. etc, etc,
To make a body lift you need for a Lwb 10 x approx 70mm diam by 50mm long aluminium or steel spacers with a 13mm hole in the middle. Plus 10
of 150 x 12mm bolts, washers and nyloc nuts.
Follow the above and common sense. Its NOT a hard job.
Have fun, and take your time.
I just prefer Ally but steel is ok. I havnt used nylon. If its hard it should be ok. Run a 12 to 13 mm hole thru the middle.
The mounts are 70mm. So min is this size . 80 is better. Under door mounts will need a slight chamfer on inner top edge if using larger than 72 as floor mount curves slightly. Check when fitting.
Bolts should be proportionately shorter than listed below. Rear two need to be longer by about 25/30,mm to allow for captive nut size.
Remove carpets, seatbelt bottom bolts.Bottom clip on plastic bit on fan cowling.
Undo all bottom nuts and two rear bolts. (use heat inside floor to break the loctite ion these two) You can drill these captive nuts out to allow the use of longer thru bolts from the top the same as all the others.
I sometimes have had to cut floor here with tin snips to get to nuts, then just screw an ally plate over hole.
Jack up truck body with bits of wood on trolley jacks front and rear until body comes clear of mounts. Check every where for binding., fuel hoses etc.
Keep lifting until new spacers can be slid in, using a bit of grease to reduce corrosion later, take care of fingers.
When istalling a body lift check the following:
1. Steering slip joint to shaft, slide down a bit to relieve stress
2. Brake coiled pipe between body and chassis (under master cyl) open them up
3. Cable loom (under passenger seat) to chassis
4. Clutch flexible pipe from gearbox to body, bend down body bracket
5. Remove small shroud extension from bottom of radiator.
6. Replace fuel feed and return hoses, body to fuel pump, with longer ones - esp on diesel.
7. Check air con hoses from pump up to body isnt snagging.
8. Low range lever will need mod to it and surrounding area, more so on GQ1s.
9. Gearlever aperture likewise for 2nd, 4th and rev.
10. etc, etc,
To make a body lift you need for a Lwb 10 x approx 70mm diam by 50mm long aluminium or steel spacers with a 13mm hole in the middle. Plus 10
of 150 x 12mm bolts, washers and nyloc nuts.
Follow the above and common sense. Its NOT a hard job.
Have fun, and take your time.
Posts: 3825
Joined: Wed Nov 06, 2002 8:42 pm
Joined: Wed Nov 06, 2002 8:42 pm
Location: in the sky , its a bird , its a plane ! No its super MOOSE !!!
digi camera !!!
dont have a digi !!!!!!
will have to talk to BESTY !!! , to come in & take some shots !!!!
chassis lift !
rear 1/4 cut !
rear bar to suit !
gaurd cut & roll !
ute conversion !
the list goes on !!!!!!!
will have to talk to BESTY !!! , to come in & take some shots !!!!
chassis lift !
rear 1/4 cut !
rear bar to suit !
gaurd cut & roll !
ute conversion !
the list goes on !!!!!!!
MissForbyNoob wrote:
and one day i'll just become a worthless housewife.
and one day i'll just become a worthless housewife.
Posts: 3825
Joined: Wed Nov 06, 2002 8:42 pm
Joined: Wed Nov 06, 2002 8:42 pm
Location: in the sky , its a bird , its a plane ! No its super MOOSE !!!
pics !!
terra , pics on another thread !!!!!
http://www.outerlimits4x4.com/PHP_Modul ... php?t=1960
http://www.outerlimits4x4.com/PHP_Modul ... php?t=1960
MissForbyNoob wrote:
and one day i'll just become a worthless housewife.
and one day i'll just become a worthless housewife.
Posts: 3825
Joined: Wed Nov 06, 2002 8:42 pm
Joined: Wed Nov 06, 2002 8:42 pm
Location: in the sky , its a bird , its a plane ! No its super MOOSE !!!
lowered !!!
luv the lowered laser carlton !!!!!!
MissForbyNoob wrote:
and one day i'll just become a worthless housewife.
and one day i'll just become a worthless housewife.
hey for the bolts ... do u's have a fully threaded bolt?
I have all the stuff I need cept for the bolts ...
what bolts do I need ... says 150mm long in the write up .. is this correct?
will high tensile steel bolt be enough?
I have all the stuff I need cept for the bolts ...
what bolts do I need ... says 150mm long in the write up .. is this correct?
will high tensile steel bolt be enough?
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Who is online
Users browsing this forum: No registered users and 0 guests