Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Tranfer case Questions

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 399
Joined: Sat Oct 31, 2009 9:16 pm
Location: Nth Richmond. NSW

Tranfer case Questions

Post by Black Bull »

Got asked today, how to make the push button transfer case of an LN130 work without the matching harness/Computer.
Had to admit I didn't know as I've never come across it

Can it be done or would he be better going back to the early transfer case of a G52 such as is in my Hilux
Top
Posts: 1167
Joined: Tue Jun 16, 2009 10:42 am
Location: campbelltown

Re: Tranfer case Questions

Post by MogLux »

Do you have wiring diagram for the LN130 gearbox/transfer case it couldnt be that hard. I have a mate with a surf chain drive box behind a early model manual gbox and the 4wd works of a switch then you have the lever. If you can send me a diagram ill have a look at it for you
Hell Raiser 4 seat social buggy..
Thanks to RDG Engineering, OverKill Engineering, Locktup 4x4 and C&D Automotive
Top
Posts: 399
Joined: Sat Oct 31, 2009 9:16 pm
Location: Nth Richmond. NSW

Re: Tranfer case Questions

Post by Black Bull »

macarthur 4x4 wrote:Do you have wiring diagram for the LN130 gearbox/transfer case it couldnt be that hard. I have a mate with a surf chain drive box behind a early model manual gbox and the 4wd works of a switch then you have the lever. If you can send me a diagram ill have a look at it for you
I had figured as much, but wasn't sure. if it's just a matter of switching current to a solenoid I'll be able to figure it out
Top
Posts: 1167
Joined: Tue Jun 16, 2009 10:42 am
Location: campbelltown

Re: Tranfer case Questions

Post by MogLux »

Black Bull wrote:
macarthur 4x4 wrote:Do you have wiring diagram for the LN130 gearbox/transfer case it couldnt be that hard. I have a mate with a surf chain drive box behind a early model manual gbox and the 4wd works of a switch then you have the lever. If you can send me a diagram ill have a look at it for you
I had figured as much, but wasn't sure. if it's just a matter of switching current to a solenoid I'll be able to figure it out
Just ensure the soleniod is 12volt as the computer may reduce it down. More than likely it will be 12volt though.
Hell Raiser 4 seat social buggy..
Thanks to RDG Engineering, OverKill Engineering, Locktup 4x4 and C&D Automotive
Top
Posts: 1231
Joined: Sun May 15, 2005 1:00 pm
Location: Bayside, Brisbane

Re: Tranfer case Questions

Post by Mr DJ »

Black Bull, the Surf tranny & transfer do run through a 4WD ECU but should not be required for Mr S's purpose.
There is a black box (shifter wiring goes to - from this to 4WD ECU) that is attached to the shifter that may be needed tho.
Without this may need to permamently engage the "red button" via the solenoid just in front of the shifter, or just run a feed from the brake light circut to activate.

HTH.
91' Hilux Surf with the usual mods & a few different ones ....
Coil SAS by www.budscustoms.com.au
Top
Posts: 745
Joined: Sat Aug 02, 2008 9:45 am
Location: Vanuatu/ QLD

Re: Tranfer case Questions

Post by thrashlux »

have done it before there is a reversible elec motor with 2 limit switches
you need to set up a switch with 2 relays to stop it over driving
if you dont connect the relays to the limit switches the thing can jam in 4x4
80 series 1980 hilux cab supra twin turbo engine
1hdfte 80 series
LHD fz 80 series GX
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 1 guest