Hiya fellas,
I'm after some advice on finding some non-setting sealant.
I need to seal a small access panel on my firewall and need some sort of sealant for it.
I have used Sikaflex & Silastic before but it goes hard when cured so is not raelly of much use. I have thought of silicon grease but it will go runny in the engine bay.
I was also thinking of liquid gasket maker (ultra blue) but I think it goes hard when cured as well.
Do you guys know of anything suitable?
Thanks
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Non-setting sealant
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Re: Non-setting sealant
Last I was in autobarn there were 'non hardening' sealants.
May be what you want.
May be what you want.
ferog wrote:I've had worse smelling fingers though.
Re: Non-setting sealant
We use 'D-mastic' which is a non setting sealant that 'skins' when we do some roofing and body work on busses/coaches.
http://www.selleys.com.au/car-care/sealants/d-mastic" onclick="window.open(this.href);return false;
not sure how it would go with the heat in an engine bay though.
you tried sending a sikaflex rep an email???
http://www.selleys.com.au/car-care/sealants/d-mastic" onclick="window.open(this.href);return false;
not sure how it would go with the heat in an engine bay though.
you tried sending a sikaflex rep an email???
Real men smoke clutches
86' Pajero
2" OME, steel bar goodness, MTZ's, Exxon Valdez-esk fuel consumption
86' Pajero
2" OME, steel bar goodness, MTZ's, Exxon Valdez-esk fuel consumption
Re: Non-setting sealant
What is that black or grey stuff they use to hold the plastic behind the door cards on?? that might work!!
if ya gona rev it, Chev it
Re: Non-setting sealant
You can get mastic that forms a skin but still soft underneath.
AMADAXTREME Racing
Sponsors-
AmadaXtreme
Superior Engineering
www.superiorengineering.com.au/
Sponsors-
AmadaXtreme
Superior Engineering
www.superiorengineering.com.au/
Re: Non-setting sealant
Just phoned Selleys. The D-Mastic has an operating temp of 10-70 deg C so I don't think it's really suitable for engine bays... or maybe it is but it may get soft.NCpaj wrote:We use 'D-mastic' which is a non setting sealant that 'skins' when we do some roofing and body work on busses/coaches.
http://www.selleys.com.au/car-care/sealants/d-mastic" onclick="window.open(this.href);return false;
not sure how it would go with the heat in an engine bay though.
you tried sending a sikaflex rep an email???
Re: Non-setting sealant
I've used the selleys mastic on the fire wall/footwell where i repaired some rust. I stitched in some zinc seal sheet that over lapped a lil, couple of coats of paint then mastic inside and out to help seal then more over the top. 4 years on its still good.
Re: Non-setting sealant
There's some permatex gray sealant that Supercheap sell that skins up but doesn't set. It's fuel resistant but not sure about heat.
Who is online
Users browsing this forum: No registered users and 142 guests