FAb shops in Brisbane to fabricate a new pulley?

Post by **Braddels** » Fri Nov 11, 2011 7:23 pm

As the title suggests,
I need a new idler pulley fabed up as the one I have now has been worn down. It was part of the sprintex supercharger kit but they no longer sell/ Make them. I will be heading down in December so I was looking at taking it with me and having it reverse engineered and a new one made up. Can anyone recommend a Fab shop that would be able to do this or should I try a bearing shop?
Cheers for your thoughts.

Post by **ledgend80** » Fri Nov 11, 2011 9:54 pm

you got a pic

Post by **Braddels** » Sat Nov 12, 2011 8:05 pm

Will take one on Monday. If it helps?

Post by **phippsy** » Sun Nov 13, 2011 3:45 pm

I've used Smart Engineering at Archerfield for work stuff a couple of time to do exactly this, remachine keyways etc. Work has always been spot on.

Post by **Braddels** » Sun Nov 13, 2011 8:08 pm

What sort of hourly rate did they charge? Close to where I will be so I might stop in and have a chat.

Post by **stock 4runner** » Mon Nov 14, 2011 6:06 am

Mate we could more then likely do it at my work shop and I have a mate in gove that might be able to bring it back earlier but a pic would help a lot mate

Post by **bru21** » Mon Nov 14, 2011 8:49 am

I had CDQ eng. on the sunny coast build me one. $200 odd. He has a cnc lathe! Paul is the guy you need to talk too. He has done heaps of work for me inc winch drums, circlip mod to the brake drum etc

Post by **Going_up** » Fri Nov 18, 2011 9:09 am

I used to work for Jack Bros. Enngineering in Springwood,

Give them a call, I did quite a few of them while i was there. they know their stuff. Prob one of the best in the biz

Post by **Braddels** » Fri Nov 18, 2011 11:57 am

Thanks for the replies and suggestions fellas. I just spoke with Greg from Bullet cars and he sugested that I take the Rosta tensioner arm and pulley to CBC and they should be able to help me out. Rosta arm died when it was comming out

. So its back to N/A for a while until I get to Brisbane. If I have no luck at CBC I will call the places that you have named. Time for a beer :drinking:

then back to skinning knuckles getting a stripped bolt out

.

Post by **351ciofgrunt** » Sat Nov 26, 2011 7:24 am

I used Zenith Engineering in Milton to make a bigger diameter alternator pulley for me, they only charged $160 and it was good work

Post by **AFeral** » Sat Nov 26, 2011 8:50 pm

Highly recomend stock 4runners work would recommend trying him.

Post by **SIM79** » Sun Feb 19, 2012 3:51 pm

bru21 wrote:I had CDQ eng. on the sunny coast build me one. $200 odd. He has a cnc lathe! Paul is the guy you need to talk too. He has done heaps of work for me inc winch drums, circlip mod to the brake drum etc

Thanks this info, I need a new drum for my PTO.

Outer Limits 4x4 Board

FAb shops in Brisbane to fabricate a new pulley?

FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Re: FAb shops in Brisbane to fabricate a new pulley?

Who is online