Im trying to space down the front hanger to get rid of some of angle on the spring. Wondering what everyone thought of two plates of 10mm shooting down from the chassis to form new hanger. I think it would work well.
Im doing a soa at the moment so i have steering knuckles and perches free to move.
heres awesome diagram
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
shackle reversal
Moderators: toaddog, TWISTY, V8Patrol, Moderators
shackle reversal
Gq patrol
Pretty sure mine is similar, BUT, between the chassis and the spring mount is a piece of steel box section, it's welded to the chassis, and the spring mount is welded underneath this, steel plates like you're talking of run over the sides to strengthen everything.
Mick
Mick
There are no stupid questions, but there are a LOT of inquisitive idiots
What brand and type of vehicle have you got ? If its a Landcruiser you should drill a bleed hole in the front prop shaft slip joint because the axle will want to move rearwards when you hit a bump. The toyota slip joints hydraulically lock with the grease inside, this pushes against your transfercase and may crack it in time.
You should also expect reduced offroad ability due to front axle tramp.
It will be similar to an old leaf sprung LandRover.
Bill.
You should also expect reduced offroad ability due to front axle tramp.
It will be similar to an old leaf sprung LandRover.
Bill.
I think its a shorty mq, I'm at work til 7 and will be tommorow 
I'll see how i go with a camera on tuesday.
na, its a different mount at the rear and yea it is reinforced, doesn't have to be overly beefed up tho as it sits right on the chassis rail, just some bracing either side.
I'll see how i go with a camera on tuesday.
na, its a different mount at the rear and yea it is reinforced, doesn't have to be overly beefed up tho as it sits right on the chassis rail, just some bracing either side.
There are no stupid questions, but there are a LOT of inquisitive idiots
Sorry mate couldn't get a piccy, but had a close look at it next to my stock mk,
Firstly the front mounts are wider than the chassis so your idea wouldn't fit the springs in, unless u spaced it out which would make it weak.
How my front mounts are set up are:
50mm OD box section with capped ends, (the chassis is about 50mm wide)
This is simply welded onto the botton of the chassis rails, it is only as long as the front mount.
The mount itself is actually identical to the standard rear mount, it's just welded to the bottom of the box under the chassis rail, the only difference is that it doesn't have the plates on the side like the rear mount (i said it did before but stuffed up).
The rear mount is just thick walled tube sized to fit the bushes for the shackle and fit between the shackle, its welded to the chassis and is gusseted at the front.
Hope that helps a bit.
Mick
Firstly the front mounts are wider than the chassis so your idea wouldn't fit the springs in, unless u spaced it out which would make it weak.
How my front mounts are set up are:
50mm OD box section with capped ends, (the chassis is about 50mm wide)
This is simply welded onto the botton of the chassis rails, it is only as long as the front mount.
The mount itself is actually identical to the standard rear mount, it's just welded to the bottom of the box under the chassis rail, the only difference is that it doesn't have the plates on the side like the rear mount (i said it did before but stuffed up).
The rear mount is just thick walled tube sized to fit the bushes for the shackle and fit between the shackle, its welded to the chassis and is gusseted at the front.
Hope that helps a bit.
Mick
There are no stupid questions, but there are a LOT of inquisitive idiots
Who is online
Users browsing this forum: No registered users and 2 guests