Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
MQ/MK gearing
MQ/MK gearing
Does any one make diffrent gear ratios for the mq/mk for when you fit bigger tyres...
No after market manufacturer makes improved gearing for MQ/MK.\
4.625 is the highest common diff centre gearing you can get. You can also get 4.8's but they are very uncommon as they only made an appearance in the late model MK utes.
You can improve your gearing in the gearbox also, fitting a 5 speed gives you a much lower first and second, if its from a naturally asperated diesel that figure is even lower then from the turbo diesel 5 speeds.
my rig had no problems at all ( towed near 3 tonne in overall added wieght down to Kingys ( 13 hours down the freeway, sitting on 100km to 120km per hour the whole time cept up hills... ) with the standard diesel and 35's on standard 4.625 gearing.
screwy
4.625 is the highest common diff centre gearing you can get. You can also get 4.8's but they are very uncommon as they only made an appearance in the late model MK utes.
You can improve your gearing in the gearbox also, fitting a 5 speed gives you a much lower first and second, if its from a naturally asperated diesel that figure is even lower then from the turbo diesel 5 speeds.
my rig had no problems at all ( towed near 3 tonne in overall added wieght down to Kingys ( 13 hours down the freeway, sitting on 100km to 120km per hour the whole time cept up hills... ) with the standard diesel and 35's on standard 4.625 gearing.
screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
u could probably have them made but it will cost u so much its not worth while.
My rig and V8 patrols, have both run 38's with a 5 speed and 4.6's Runs 's them fine. Mine will be permenatly on 38s after this finaly biuld up.
We both have V8's though.... But the diesel will pull 38's as well just wont like it much...
screwy
My rig and V8 patrols, have both run 38's with a 5 speed and 4.6's Runs 's them fine. Mine will be permenatly on 38s after this finaly biuld up.
We both have V8's though.... But the diesel will pull 38's as well just wont like it much...
screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
From the European FAST parts system, it looks like the 160/R model (83-88) SD33-powered pickup/trayback models came with 4.875 gears.
In search of an MQ (offset) H233b rear, housing only preferred, plus a complete GQ or GU front (4.6 ratio ideal) to be shipped to the US. Cheap! Email/PM if you can help.
XterraGuy wrote:From the European FAST parts system, it looks like the 160/R model (83-88) SD33-powered pickup/trayback models came with 4.875 gears.
Yes, As i said above, the late model MK utes came out with 4.8's but they are rare and expensive for little improvement.
If u bust one or up for a load or crap in trying to find one much less the cost.
4.6s are common and stronger too.
screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Cant get it because there is no demand for it. If you want low gears in the T-case ( personaaly cant justafy spending that much when MQ's have good enough gearing to get ya home ) Get a turbo 700 auto and fit a 40 or 60 series transfer on it. They are offset and you can get crawlet gears for them.
Or
Fit a GQ box but theres even more stuffen around there, as MQ diffs are offset and GQs arnt, so u will need GQ diffs as well if u plan on any major lift, so therefore, may as well get a GQ if ya want to go that far....
screwy
Or
Fit a GQ box but theres even more stuffen around there, as MQ diffs are offset and GQs arnt, so u will need GQ diffs as well if u plan on any major lift, so therefore, may as well get a GQ if ya want to go that far....
screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Who is online
Users browsing this forum: No registered users and 1 guest