Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Hydro bumpstops.
Moderators: toaddog, TWISTY, V8Patrol, Moderators
daisy is looking mighty cute in that there hide 
bj on roids wrote:i think the colours mean you might be sexually deprived?
don't worry dude, not long now and you can be morally correct while banging it8)
it looks very cute with all those colours, i might do something similar (paint underneath me truck like that)
Make sure you chrome your driveshafts too!
cplux wrote:Before that idea was even posted i was thinking a similar setup to force more down travel with my chevys, does anyone think it would work.
I think that for any of this stuff that air has to be the way to go. It would have to be cheeper and you dont have to connect the air ram to the suspension with a flexable link (cause the air is already flexable) so the system would be a lot simpler as well.
Sam
Sam,
yes a pneumatic system does have some advantages, eg. cushioning, although speed at higher pressures is a concern, as to create the same force requirement for the same cylinder bore diameter, the same pressure is needed. Even for a relatively light vehicle such as a lux or zook approx 1ton of force is required at each rear wheel, as during climbing or off camber situations the majority of the vehicle weight could be on one point. A direct acting ram onto the diff at an outer point is ideal as it reduces the induced torque arm effect of location, but this ram must also have enough available stroke to allow full travel, often up to 20inches which can be quite expensive. Also being used in such a harsh enviroment mounting the cylinder out of the road is prefferable, another thing to consider in a long ram is the rod/stroke/neckbush ratio which in shock loading situations can cause cylinder buckling even in pneumatic cylinders. But you are correct implementing a cushioning circuit is the way to go & a hydrocushion tank can be fitted to each ram and adjusted to individual requirements(torque, vehicle weight, max compression). By utilising this feature you can power up/down each corner, or raise/lower each end & still have a cushioned ride(although a lot stiffer when fully loaded. Air is good , but hydraulic is better especially when it come time to buy the valving, heaps cheaper, more options & if something breaks just go into a nearby baddock & pinch it of a farmers tractor!! only kidding!.
below is another idea using a dodgy 4link i sketched up, please excuse the drawing as it was real quick, I didnt even have time to draw the other ram, so you just have to imagine the rams are symetrical(2 off, fro each side).
yes a pneumatic system does have some advantages, eg. cushioning, although speed at higher pressures is a concern, as to create the same force requirement for the same cylinder bore diameter, the same pressure is needed. Even for a relatively light vehicle such as a lux or zook approx 1ton of force is required at each rear wheel, as during climbing or off camber situations the majority of the vehicle weight could be on one point. A direct acting ram onto the diff at an outer point is ideal as it reduces the induced torque arm effect of location, but this ram must also have enough available stroke to allow full travel, often up to 20inches which can be quite expensive. Also being used in such a harsh enviroment mounting the cylinder out of the road is prefferable, another thing to consider in a long ram is the rod/stroke/neckbush ratio which in shock loading situations can cause cylinder buckling even in pneumatic cylinders. But you are correct implementing a cushioning circuit is the way to go & a hydrocushion tank can be fitted to each ram and adjusted to individual requirements(torque, vehicle weight, max compression). By utilising this feature you can power up/down each corner, or raise/lower each end & still have a cushioned ride(although a lot stiffer when fully loaded. Air is good , but hydraulic is better especially when it come time to buy the valving, heaps cheaper, more options & if something breaks just go into a nearby baddock & pinch it of a farmers tractor!! only kidding!.
below is another idea using a dodgy 4link i sketched up, please excuse the drawing as it was real quick, I didnt even have time to draw the other ram, so you just have to imagine the rams are symetrical(2 off, fro each side).
WWW.TEAMDGR.COM
WWW.SUPERIORENGINEERING.COM.AU
WWW.LOCKTUP4X4.COM.AU
WWW.SUPERIORENGINEERING.COM.AU
WWW.LOCKTUP4X4.COM.AU
The best way to run 1/4 is like the sniper, where the 1/4 spring pack pivots forced down by an airbag system. This is the way the adjust ride height and is an optional system for leveling. As most people would agree air levelling is way too slow, on even the best rigs , especially for competition. From your pics i think you already have the top of the 1/4 spring packs pivoting so all you have to do is use 2 rams to adjust height & as tony & sam said use the bottom 2 leaves to maintain tension in over extended off camber situations. If what i explained isn't clear (probably not i do talk in odd terms) i would love to have a chat about different ideas.
Greg...
PM me if you want
Greg...
PM me if you want
WWW.TEAMDGR.COM
WWW.SUPERIORENGINEERING.COM.AU
WWW.LOCKTUP4X4.COM.AU
WWW.SUPERIORENGINEERING.COM.AU
WWW.LOCKTUP4X4.COM.AU
Its pretty awesome shait 1 mad comes up with, most of the times i need him to draw it and explain it to me about ten times before i get the drift, but its pretty functional too.
One of the main reason behind the ram set up above is so you can use a relatively short ram stroke and utilise the levers for more downward movement.
And like my set up i dont have enough room to mount a ram onto my lower control arms, so this would come in handy.
Greg,
Explain the ram idea you showed me, about putting rams on top of my springs.
One of the main reason behind the ram set up above is so you can use a relatively short ram stroke and utilise the levers for more downward movement.
And like my set up i dont have enough room to mount a ram onto my lower control arms, so this would come in handy.
Greg,
Explain the ram idea you showed me, about putting rams on top of my springs.
1 Mad what you said does make sense to me.
I'll test the car first and see how it drives we are mounting the shocks virtically this time which will also help. I will contact you and we can through some ideas around.I don't know wy more people haven't tried 1/4 elliptic. As it is a cheap way of getting a lot of travel.
I'll test the car first and see how it drives we are mounting the shocks virtically this time which will also help. I will contact you and we can through some ideas around.I don't know wy more people haven't tried 1/4 elliptic. As it is a cheap way of getting a lot of travel.
1MadEngineer wrote:Sam,
yes a pneumatic system does have some advantages, eg. cushioning, although speed at higher pressures is a concern, as to create the same force requirement for the same cylinder bore diameter, the same pressure is needed. Even for a relatively light vehicle such as a lux or zook approx 1ton of force is required at each rear wheel, as during climbing or off camber situations the majority of the vehicle weight could be on one point. A direct acting ram onto the diff at an outer point is ideal as it reduces the induced torque arm effect of location, but this ram must also have enough available stroke to allow full travel, often up to 20inches which can be quite expensive. Also being used in such a harsh enviroment mounting the cylinder out of the road is prefferable, another thing to consider in a long ram is the rod/stroke/neckbush ratio which in shock loading situations can cause cylinder buckling even in pneumatic cylinders. But you are correct implementing a cushioning circuit is the way to go & a hydrocushion tank can be fitted to each ram and adjusted to individual requirements(torque, vehicle weight, max compression). By utilising this feature you can power up/down each corner, or raise/lower each end & still have a cushioned ride(although a lot stiffer when fully loaded. Air is good , but hydraulic is better especially when it come time to buy the valving, heaps cheaper, more options & if something breaks just go into a nearby baddock & pinch it of a farmers tractor!! only kidding!.
below is another idea using a dodgy 4link i sketched up, please excuse the drawing as it was real quick, I didnt even have time to draw the other ram, so you just have to imagine the rams are symetrical(2 off, fro each side).
Lots of bending moment on the lower link. The idea of pin jointed links is to have zero bending moment - yes?
74 FJ40, 307, Hilux DBC, 35 Claws, welded rear.
'''_ ______
'/|_[_____]__
|?[_L/-\_|o=o|_
?:__;-?__-,==,_
()_)O()_)O== )_)
'''_ ______
'/|_[_____]__
|?[_L/-\_|o=o|_
?:__;-?__-,==,_
()_)O()_)O== )_)
if i can get the money together i should be able to convince 1mad to fit it to my car front and rearhopefully before xrcc .stil cant afford computor for v8dont want to run carby so staying with 4 cyl for now. but preparing for 1mads system now 
FOR SALE hilux parts all models
have most parts available from early to late
call mick 0415156693
have most parts available from early to late
call mick 0415156693
2car wrote:1MadEngineer wrote:Sam,
yes a pneumatic system does have some advantages, eg. cushioning, although speed at higher pressures is a concern, as to create the same force requirement for the same cylinder bore diameter, the same pressure is needed. Even for a relatively light vehicle such as a lux or zook approx 1ton of force is required at each rear wheel, as during climbing or off camber situations the majority of the vehicle weight could be on one point. A direct acting ram onto the diff at an outer point is ideal as it reduces the induced torque arm effect of location, but this ram must also have enough available stroke to allow full travel, often up to 20inches which can be quite expensive. Also being used in such a harsh enviroment mounting the cylinder out of the road is prefferable, another thing to consider in a long ram is the rod/stroke/neckbush ratio which in shock loading situations can cause cylinder buckling even in pneumatic cylinders. But you are correct implementing a cushioning circuit is the way to go & a hydrocushion tank can be fitted to each ram and adjusted to individual requirements(torque, vehicle weight, max compression). By utilising this feature you can power up/down each corner, or raise/lower each end & still have a cushioned ride(although a lot stiffer when fully loaded. Air is good , but hydraulic is better especially when it come time to buy the valving, heaps cheaper, more options & if something breaks just go into a nearby baddock & pinch it of a farmers tractor!! only kidding!.
below is another idea using a dodgy 4link i sketched up, please excuse the drawing as it was real quick, I didnt even have time to draw the other ram, so you just have to imagine the rams are symetrical(2 off, fro each side).
Lots of bending moment on the lower link. The idea of pin jointed links is to have zero bending moment - yes?
Yeah, but by applying a load along one of the links like in that setup, the link is becoming a beam, not just a tension / compression member.
1MadEngineer wrote:The (pink) Rod in the pic is a torque rod eg. front IFS which allows for movement of the diff even under "driven" articulation, which is something most systems dont allow for.!! Also the beauty that it can be adapted to most 3link designs....
Mad I may have missed something but arn't Torsion boars designed to load up in one direction.......
I was just thinkin of the loading on the materials used and metal fatigue would be a concern in the torsion component of that setup....
Just curious interesting idea though
Official member of the Babinda Jimmy James Beam III Fan Club
Darth Bobo Honker Hunter Inc, for the up gunned Poodlefaker.
:armsup:"ARMS UP":armsup:
Darth Bobo Honker Hunter Inc, for the up gunned Poodlefaker.
:armsup:"ARMS UP":armsup:
DirtPig wrote:2car wrote:1MadEngineer wrote:Sam,
yes a pneumatic system does have some advantages, eg. cushioning, although speed at higher pressures is a concern, as to create the same force requirement for the same cylinder bore diameter, the same pressure is needed. Even for a relatively light vehicle such as a lux or zook approx 1ton of force is required at each rear wheel, as during climbing or off camber situations the majority of the vehicle weight could be on one point. A direct acting ram onto the diff at an outer point is ideal as it reduces the induced torque arm effect of location, but this ram must also have enough available stroke to allow full travel, often up to 20inches which can be quite expensive. Also being used in such a harsh enviroment mounting the cylinder out of the road is prefferable, another thing to consider in a long ram is the rod/stroke/neckbush ratio which in shock loading situations can cause cylinder buckling even in pneumatic cylinders. But you are correct implementing a cushioning circuit is the way to go & a hydrocushion tank can be fitted to each ram and adjusted to individual requirements(torque, vehicle weight, max compression). By utilising this feature you can power up/down each corner, or raise/lower each end & still have a cushioned ride(although a lot stiffer when fully loaded. Air is good , but hydraulic is better especially when it come time to buy the valving, heaps cheaper, more options & if something breaks just go into a nearby baddock & pinch it of a farmers tractor!! only kidding!.
below is another idea using a dodgy 4link i sketched up, please excuse the drawing as it was real quick, I didnt even have time to draw the other ram, so you just have to imagine the rams are symetrical(2 off, fro each side).
Lots of bending moment on the lower link. The idea of pin jointed links is to have zero bending moment - yes?
Yeah, but by applying a load along one of the links like in that setup, the link is becoming a beam, not just a tension / compression member.
Correct.
74 FJ40, 307, Hilux DBC, 35 Claws, welded rear.
'''_ ______
'/|_[_____]__
|?[_L/-\_|o=o|_
?:__;-?__-,==,_
()_)O()_)O== )_)
'''_ ______
'/|_[_____]__
|?[_L/-\_|o=o|_
?:__;-?__-,==,_
()_)O()_)O== )_)
Who is online
Users browsing this forum: No registered users and 0 guests