ok, so i just went and got a h55f out of an 84 bj42 to go behind the 3b in my lux.
goddamn, its heaps shorter and higher than the lux box and transfer i had been previously running.
so. i have a problem with the length of the front tailshaft. i'm moving the diff further forward again to help this problem.
does anyone know of a dual case kit for this transfer/gearbox as it would give me lower ratios and also the extra tailshaft length i need???
cheers
james
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
cruiser dual cases in lux??
Moderators: toaddog, Elmo, DUDELUX
duals
Toybox is for 4 speed transfer case not 5 speed, Unless you buy the crawler box from mark's there is no way to get duals from crusier at the moment, although I have been looking at running lux 4 speed to crusier but have not gotten far with this yet.... nowhere really but will let you know if it happens.
[/i]
[/i]
83 60 Series cruiser, 33 Muddies, Rear locker, UHF, Custom Boxes, Pleanty dints.
ok, so i can't move the output flange further back using a second transfer case.
appreciate your help guys.
i am putting the rear springs in the front, using the rear hole in the spring perch. this should move the diff a fair way forward, away from the transfer. probably gain about 50mm from this.
also i will have to move the engine back my making new mounts on the chassis, both lower and further back. probably get 60mm from this.
as a long shot could i machine up a spacer between the gearbax and transfer say 100mm long with an extension shaft with both male and female splines to link the gearbox and transfer once they are moved apart. jees i hope it doesn't come to this, too much work
anybody got any other ideas???
appreciate your help guys.
i am putting the rear springs in the front, using the rear hole in the spring perch. this should move the diff a fair way forward, away from the transfer. probably gain about 50mm from this.
also i will have to move the engine back my making new mounts on the chassis, both lower and further back. probably get 60mm from this.
as a long shot could i machine up a spacer between the gearbax and transfer say 100mm long with an extension shaft with both male and female splines to link the gearbox and transfer once they are moved apart. jees i hope it doesn't come to this, too much work
anybody got any other ideas???
Work out just how much shorter your drivetrain will be, because you may be able to move the front diff forward enough to use standard lux front shaft.
By putting rears up front you can get the front diff up to 5 inches forward: if you mount new dropped spring hangers 1" or 2" forward (recommended anyway)- more room if you move the diff forward on it's spring perches. (Will need X over steering tho).
So I'd do the spring swap to suit your drivetrain and save a few dollars with the front shaft.
By putting rears up front you can get the front diff up to 5 inches forward: if you mount new dropped spring hangers 1" or 2" forward (recommended anyway)- more room if you move the diff forward on it's spring perches. (Will need X over steering tho).
So I'd do the spring swap to suit your drivetrain and save a few dollars with the front shaft.
Who is online
Users browsing this forum: No registered users and 6 guests