Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Thoughts on twin t cases
Thoughts on twin t cases
Guys looking for some input as im streching the rear section of the wheel base by 21 inches and am going to run a hilux double cardon joint was thinking of dual cases as i definatly have the room to fit them.What case has the lowest ratios
Dozoor wrote:You may achieve a lower ratio , BUt you,ll also suck another 10- 15%
of the power from your motor . Less gears equals more power .
The only reason ican think of is to keep the high range ratio's at standard,
With some reduction gearing it lowers the high range as well, like 25% in the series 3 rock hoppers.
Tim D wrote:Dozoor wrote:You may achieve a lower ratio , BUt you,ll also suck another 10- 15%
of the power from your motor . Less gears equals more power .
The only reason ican think of is to keep the high range ratio's at standard,
With some reduction gearing it lowers the high range as well, like 25% in the series 3 rock hoppers.
ahhh rong even with standard gears in both cases it will be still very low in high high i think high high 1st gear would be ruffley 30:1
u gotta rember zuk cases dont have 1:1 in high range
Team UNDERDOG #233
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
Hi Duncan
I like the way you are thinking,have been doing some reading on this subject.
TRY HERE
http://www.zookpower.ca/forums/showthread.php?t=1012
Lots of photo's,this site puts last post first so you have to go to page 7 to get to the start
Cheers Simon
I like the way you are thinking,have been doing some reading on this subject.
TRY HERE
http://www.zookpower.ca/forums/showthread.php?t=1012
Lots of photo's,this site puts last post first so you have to go to page 7 to get to the start
Cheers Simon
Thanks guys was just considering costs ie twins against series 3s as im going to have heaps of room .Was going to go series 3s but now no of 2 people who have destroyed theres and are having warranty problems because there gears dont have any stamped markings on them but both were bought at offical out lets and fitted by mechanics who do this kind of work all the time .So do i go series 3s at 6.1 to 1 or go Calmini at a higher ratio or try to hook up twins ?.Can anyone get a good deal on either sets of lower gears
duncan wrote:Thanks guys was just considering costs ie twins against series 3s as im going to have heaps of room .Was going to go series 3s but now no of 2 people who have destroyed theres and are having warranty problems because there gears dont have any stamped markings on them but both were bought at offical out lets and fitted by mechanics who do this kind of work all the time .So do i go series 3s at 6.1 to 1 or go Calmini at a higher ratio or try to hook up twins ?.Can anyone get a good deal on either sets of lower gears
trail tough 6.4:1
or rocky road 8:1
Team UNDERDOG #233
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
Of course If the real benifit was to create a variable range box , and
power wasnt a priority
and would give a huge range of ratio options , the swedes have been using a simple second gearbox in place of the jack shaft , they use a volvo box , . Don,t know how strong they would be . But We do have a few great box,s over here that would certianly
Make for an exellent range of ratios .
Early F100s - Run a T18 this can be found - easy its a fiarly narrow box and short , but is quiet Tall .
Achievable result would be - about 42 forward and 8 reverse ratios
Using standard zook box and transfer plus t18 would give around
246-1 crawl in low low low -3.9 diffs
Lowest reverse achieved utilising reverse on your zook box and low on the t18 - is around the same.
Would be fun but , average joe like me would nuff more obsticles thru pure "sense drench" as i call it, Just to many choices
JMO 100-1 is max - even with this you probly find youself thinking on occasion i should have used 2nd if running 31-33 rubber
Nice ratio for 34-36 looking for a bit more as the tire size increases
The big numbers are good for Big rubber (44)
I just needed somwhere to dribble
One good piont about zooks is the motors pull great rpm ,
so imagine two cars with same ratios and tires in low range
one running a chev other a zook the later will give a better top end speed from the low ratio simply because it revs higher .
Dribble over ,
Just noticed a thread on pirate on the volvo setup , didn,t look though
could be just another argument hehe
power wasnt a priority
and would give a huge range of ratio options , the swedes have been using a simple second gearbox in place of the jack shaft , they use a volvo box , . Don,t know how strong they would be . But We do have a few great box,s over here that would certianly
Make for an exellent range of ratios .
Early F100s - Run a T18 this can be found - easy its a fiarly narrow box and short , but is quiet Tall .
Achievable result would be - about 42 forward and 8 reverse ratios
Using standard zook box and transfer plus t18 would give around
246-1 crawl in low low low -3.9 diffs
Lowest reverse achieved utilising reverse on your zook box and low on the t18 - is around the same.
Would be fun but , average joe like me would nuff more obsticles thru pure "sense drench" as i call it, Just to many choices
JMO 100-1 is max - even with this you probly find youself thinking on occasion i should have used 2nd if running 31-33 rubber
Nice ratio for 34-36 looking for a bit more as the tire size increases
The big numbers are good for Big rubber (44)
I just needed somwhere to dribble
One good piont about zooks is the motors pull great rpm ,
so imagine two cars with same ratios and tires in low range
one running a chev other a zook the later will give a better top end speed from the low ratio simply because it revs higher .
Dribble over ,
Just noticed a thread on pirate on the volvo setup , didn,t look though
could be just another argument hehe
dasdAS
1995 Vitara:
stock standard
WWW.DARWIN4X4.NET
stock standard
WWW.DARWIN4X4.NET
One thing to remember with duals is all of the custom work involved - EVERYTHING ends up played with so while you might think that getting warranty on a busted series 3 is a pain, trying to iron out all of the bugs in a dual transfer set up will be more of a pain. I don't know how much use you car will get, but if it does a lot of kays, I reckon you will have trouble with duals as there will be heaps of stuff not running the way it was inended = wearing out quick.
Duals used to look like the way to go when you couldn't get Rockhoppers, but now, the work for return thing just counts them out.
PS once you go beyond about 70-80:1, it gets really hard to generate any wheelspeed to bump up an obstacle- if you start to run out of traction you can't fix it with a bump, so you end up being in a taller gear anyway, and all the granny gears end up being just for show. they are cool though, but not as cool as the tricks you can pull with an auto :o)
Duals used to look like the way to go when you couldn't get Rockhoppers, but now, the work for return thing just counts them out.
PS once you go beyond about 70-80:1, it gets really hard to generate any wheelspeed to bump up an obstacle- if you start to run out of traction you can't fix it with a bump, so you end up being in a taller gear anyway, and all the granny gears end up being just for show. they are cool though, but not as cool as the tricks you can pull with an auto :o)
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Duals
Dual hilux xfers has been done and is strong.
Search Pirate for scwafish's build, his was zook 1600 EFI + toy 5 speed + toy duals.
As Gwagensteve said, there will be a lot of custom stuff to do any way that you go. From memory this isn't an issue for you...
Search Pirate for scwafish's build, his was zook 1600 EFI + toy 5 speed + toy duals.
As Gwagensteve said, there will be a lot of custom stuff to do any way that you go. From memory this isn't an issue for you...
The Dual t -case set up on Zookpower is pretty easy and hassle free.MLC on there (my brother) Ran his for 3 years now. Good to go.
1985 Samurai VW 1.6 Intercooled And Tuned Turbo Diesel 4.16 T-caseToyota diff's with 4.11's locked rear Toy power steeringAntique Warn winch & 33 Super Swampers ZOOKPOWER.CA
Just got a email back from Calmini in the States and 5.14 are $550 were as 6.5 are $750 US dollars plus $158 to ship to WA works out about $944 and $1210 both are for full kits ie bearings idler shaft seals so series 3s at $1200 plus arnt looking that good .Ive got to get some gears as even with 5.29 hilux diffs my 1st gear low is only 43 to 1 not low enough for 38 Swampers with a 1.3 motor
duncan wrote:Just got a email back from Calmini in the States and 5.14 are $550 were as 6.5 are $750 US dollars plus $158 to ship to WA works out about $944 and $1210 both are for full kits ie bearings idler shaft seals so series 3s at $1200 plus arnt looking that good .Ive got to get some gears as even with 5.29 hilux diffs my 1st gear low is only 43 to 1 not low enough for 38 Swampers with a 1.3 motor
the calmini gears might be dearer(SP)? but i havent heard of breakage
did u try rocky road and trail tough?
they have 8:1 and 6.4:1 gears
Team UNDERDOG #233
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
duncan wrote:Just got a email back from Calmini in the States and 5.14 are $550 were as 6.5 are $750 US dollars plus $158 to ship to WA works out about $944 and $1210 both are for full kits ie bearings idler shaft seals so series 3s at $1200 plus arnt looking that good .Ive got to get some gears as even with 5.29 hilux diffs my 1st gear low is only 43 to 1 not low enough for 38 Swampers with a 1.3 motor
THESE ONLY COME WITH THE COUNTER SHAFT,WASHERS,BEARINGS AND GASKETS AND OIL....
NOT A FULL BEARING KIT...
Mud4b/ OPT, Cheap rates, Not cheap work. Search Opt- option offroad on facebook. Call or Sms 0439609525.. Sunshine coast, Eudlo, 4554.
Gwagensteve wrote:Duals used to look like the way to go when you couldn't get Rockhoppers, but now, the work for return thing just counts them out.
PS once you go beyond about 70-80:1, it gets really hard to generate any wheelspeed to bump up an obstacle- if you start to run out of traction you can't fix it with a bump, so you end up being in a taller gear anyway, and all the granny gears end up being just for show. they are cool though, but not as cool as the tricks you can pull with an auto :o)
RIGHT ON!
i said this once before and got flamed big time, but you are spot on. i have had both duals and crawlers and have learnt by both wheelin and competing that between 65:1 and 100:1 is ideal for any situation. if you are still strugling then the motor doesnt have enough torque! nearly everyone competing in XRCC will agree, you still need wheelspeed to bump up ledges, sometimes you just cant crawl-it!
twin tcase
hey duncan
hows it going
id say go the duals (toy dual)
much stronger than zook witch would suit running 36'' to 38'' tyres
no power loss when in hi-range 2wd & no gear reduction (2wd)
can select 1st t-case for sand driving when needing a little speed
OR
driving like the QLD boys N wanting some tyre speed to climb the rocks
or can select both t-cases for real slow rock crawlin
std WT transfer case is == 25KG
DUAL toys == 48kg
id say good trade off for added strenght
can get a OTT divorced kit for running a zook box
OR
use a kit to mount a toy box upto your zook 1.3 - 1.6 block
hows it going
id say go the duals (toy dual)
much stronger than zook witch would suit running 36'' to 38'' tyres
no power loss when in hi-range 2wd & no gear reduction (2wd)
can select 1st t-case for sand driving when needing a little speed
OR
driving like the QLD boys N wanting some tyre speed to climb the rocks
or can select both t-cases for real slow rock crawlin
std WT transfer case is == 25KG
DUAL toys == 48kg
id say good trade off for added strenght
can get a OTT divorced kit for running a zook box
OR
use a kit to mount a toy box upto your zook 1.3 - 1.6 block
You do not have the required permissions to view the files attached to this post.
Who is online
Users browsing this forum: No registered users and 3 guests