I am thinking of getting a 6.5 chev diesel fitted to my patrol. I have not as yet decided to go ahead because of forums in the USA with people there who seem to be having problems with cracked cylinder heads and also the blocks cracking near the main bearing webs.
Does anyone have any opinions on these engines?
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Chev 6.5 diesel conversion.
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Dude welcome to the board.
I don’t know much about the engines themselves apart from quite few rigs have them in WA. I assume you are getting it from Brunswick. What have they said about this?
Maybe wait till the next gymkana and ask some of the guys that run them.
I can understand why you would be concerned about this when you look at the price of the conversion!!
I don’t know much about the engines themselves apart from quite few rigs have them in WA. I assume you are getting it from Brunswick. What have they said about this?
Maybe wait till the next gymkana and ask some of the guys that run them.
I can understand why you would be concerned about this when you look at the price of the conversion!!
Re: Chev 6.5 diesel conversion.
try searching, theree was a massive thread on this 12 mths ago by a few people on the board here who install them.Malcolm wrote:Does anyone have any opinions on these engines?
Unless you have to have the extra grunt, go the 6.2. Only slightly less grunt etc but they run a bit cooler. Also you're not as likely to need an upgrade on the driveline at a later date. Talk to Scotty at Brunswick, they did a good job fitting mine.
Al
Al
Luv the sound of a diesel,
especially a Chev 6.2!
Its GONE.........Replaced by a qik HDJ105.
The bigger the boy, the bigger the TOY!!
especially a Chev 6.2!
Its GONE.........Replaced by a qik HDJ105.
The bigger the boy, the bigger the TOY!!
The block cracking in the main bearing webs is a problem with early 6.2L.
The block casting was modified, with thicker webs, when the 6.5L was introduced. Later 6.2L use the same casting (just a smaller bore).
Most head cracking can be repaired by fitting a sleeve in the water passage that the crack is in.
Later 6.5L have a high output water pump to cure this. The problem is hot spots in the head forming pockets of steam. The pockets of steam prevent water contact with the metal and thus poor heat conduction. The HO (high output) pump is able to flush the pockets of steam out of the heads.
Retro fitting the HO pump to earlier models in not practical. The HO pump is driven in the reverse rotation by a serpentine belt.
You have probably also heard of the problem with broken crankshafts. It is generaly believed that this is due to harmonic balancers with deteriorated rubber element. If there is any sign of the rubber bulging out, the balancer should be replaced. Also, if the bolt retaining the balancer is not torqued correctly the keyway in the crank flogs out.
Get an Isuzu engine from a truck instead. Either 4 or 6 cyl Isuzu (both are better than chevy diesel) and these trucks are everywhere here. BTW Isuzu designed the 6.6L duramax engine that replaced the 6.5L in chevy trucks.
The block casting was modified, with thicker webs, when the 6.5L was introduced. Later 6.2L use the same casting (just a smaller bore).
Most head cracking can be repaired by fitting a sleeve in the water passage that the crack is in.
Later 6.5L have a high output water pump to cure this. The problem is hot spots in the head forming pockets of steam. The pockets of steam prevent water contact with the metal and thus poor heat conduction. The HO (high output) pump is able to flush the pockets of steam out of the heads.
Retro fitting the HO pump to earlier models in not practical. The HO pump is driven in the reverse rotation by a serpentine belt.
You have probably also heard of the problem with broken crankshafts. It is generaly believed that this is due to harmonic balancers with deteriorated rubber element. If there is any sign of the rubber bulging out, the balancer should be replaced. Also, if the bolt retaining the balancer is not torqued correctly the keyway in the crank flogs out.
Get an Isuzu engine from a truck instead. Either 4 or 6 cyl Isuzu (both are better than chevy diesel) and these trucks are everywhere here. BTW Isuzu designed the 6.6L duramax engine that replaced the 6.5L in chevy trucks.
John
Bush65 wrote:Get an Isuzu engine from a truck instead. Either 4 or 6 cyl Isuzu (both are better than chevy diesel) and these trucks are everywhere here. BTW Isuzu designed the 6.6L duramax engine that replaced the 6.5L in chevy trucks.
This sounds like a better option dude....when the wheels fell of my landcruiser with caravan in tow, an Izuzu tilt tray dragged us back to the nearest town, cruiser, van and all, twice as fast as the old 60 could drag the van with a tail wind....
Boy they have some torque! That truck had 4.5 tonne on its back.
Andrew
Who is online
Users browsing this forum: Bing [Bot] and 1 guest