BIGGER tyres under a 94 Triton TD? Currently got 2" body lift and cranked up torsion bar, rolling on 31"Cooper ST's. Bigger tyres rub on turn in but want 33's!
Could someone tell me if using wheel spacers or offset rims would do it, and/or what is the best solution?
Cheers,
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Big wheels for Triton?
Moderator: -Scott-
What are the wheels rubbing on. On a Paj they touch the front bumper corners which you can trim.
Wheel spacer's etc increase your scrub radius which means the wheel turns through an arc instead of turning on the spot, This increases the amount the wheel moves forwards and backwards which increase's the possibility of body contact
J Top
Wheel spacer's etc increase your scrub radius which means the wheel turns through an arc instead of turning on the spot, This increases the amount the wheel moves forwards and backwards which increase's the possibility of body contact
J Top
J Top wrote:What are the wheels rubbing on. On a Paj they touch the front bumper corners which you can trim.
Wheel spacer's etc increase your scrub radius which means the wheel turns through an arc instead of turning on the spot, This increases the amount the wheel moves forwards and backwards which increase's the possibility of body contact
J Top
If the contact point is the outside of the tyre then wheel spacers will make the problem worse.
If the contact point is on the inside of the tyre then wheel spacers may help - and let the outside of the tyre hit somewhere that it used to clear.
Personally, I don't like the effects on the suspension geometry. A J Top noted, the first victim is scrub radius, which generally increases steering effort (not normally noticed with power steering) but adds extra load to steering components. Incorrect offset has a similar effect - on a 2wd car with 14" rims which were out by 13mm I was replacing one lower ball joint every year. When I got the offset back to within 6mm I never replaced another ball joint.
Just a personal opinion.
Scott
bennycee wrote:Thank's for your knowledge guys. I find the wheel rubs on the inside edge of the tire against the engine bay guard.
Anyone got any other idea's on how to get 33's under there without using a grinder!
Have you considered narrower tyres? I presume you're looking at 33x12.5-15s. 285/75-16 are about 33x11.2 - there's half an inch of clearance straight away. My MT/Rs seem skinny for a 285 - I reckon I've got the same tread width as a 265, which is nominally 10.5" wide, so you could end up with an extra inch?
Or you could try something like a 33x9.5-15. I've got a BFG All Terrain brochure listing that size - may not be common, but if it gets you your 33"? (and suits the standard rims, too!
)
Or, if you really don't want to use a grinder, consider a BFH.
Good luck,
Scott
Looked into a similar issue with mine, found that most tyre/ wheel seller issue what they call 'Navara offset' rims for paj/ triton fitment, tried a standard 'toyota offset' sunnrasia rim 15X8 with 33'X12.5' 15 and they fitted great with no rubbing etc, and that was with only supension lifting, no body lift , though I did not see if full articulation made them rub.
NF 3.0 BLK, 2.5" suspension (HD T bars, prog coils, TJM Bullbar, 31X10.5X15 Mickey T FCII & cent locking
Who is online
Users browsing this forum: No registered users and 6 guests