Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

The 36 kW story

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Posts: 284
Joined: Fri Mar 12, 2004 3:43 pm
Location: Rockhampton

Post by skootin »

OK Silly Question time Is the engine responsive of idle when not in gear.
How many KLM'S since the engine was rebuilt.
Does the engine pull hard though the rev's.
Has the pump timing been checked.
Has the valve clearances been checked.
Any of a number of problems but seat of your pants should tell you if it's got the go or not. Depending on the clearances the engine is possibly a little tight if it doesn't want to rev.
I'm not stuck I'm over here!
Watch where you driven!!!
Posts: 357
Joined: Fri Nov 07, 2003 3:30 am
Location: Mount Beauty

Post by Trusa »

For those who are interested

Back from Denco. Dyno tune improved quite a bit. They turned the boost up to 9 psi, and improved from (their figures) 36 rear wheel HP to 51 HP at 100 km/h.

Drove it back from wagga and apart from liking to rev more (possibly due to more boost?) it wasn't a whole lot better. They compared my figures to recorded figures of a Schwitzer turbo on a 3B and told me it wasn't worth changing to the smaller Schwitzer turbo kit they produce themselves.

Back to square one. Compression test happening monday as I believe this is the next step???

Any comments would be appreciated
Posts: 1826
Joined: Wed Mar 03, 2004 9:14 pm
Location: nsw

Post by plowy »

compression test for what wasn't it just rebuilt?
Posts: 748
Joined: Tue Nov 09, 2004 9:45 pm
Location: Lilydale

Post by Dzltec »

You have just gained 40% extra power at the wheels and still not happy. Are you expecting too much?? Did they not comp test it at denco after hearing your story? Surely you would have told them the whole story so they can make a full evaluation.

Just asking. What size tyres are you running? Can you post the dyno sheet??
Posts: 2765
Joined: Wed Jan 14, 2004 10:32 pm
Location: somewhere out there

Post by shorty_f0rty »

Trusa wrote:Back to square one. Compression test happening monday as I believe this is the next step???



if anything i would of thought that would of been the first step... oh well 20:20 hindsight i spose..
Built, not bought!
'84 BJ42 - sold! :(
'79 Coiled and turbo diesel'd FJ55
Posts: 357
Joined: Fri Nov 07, 2003 3:30 am
Location: Mount Beauty

Post by Trusa »

Tidy 42:
compression test has come up as Denco advised me of a small crack in the air inlet from filter to turbo. They said they didn't have the equipment to compression test a diesel (Go figure!!??). Apparently they fear dust may have been sucked in over a period of time.

Dzltec:
Denco was told the full story but chose to only dyno and not comment on condition of engine. They did say the turbo was maybe too big, but decided it was performing as well as one of their kits.

40% increase in power on paper doesn't translate to much on the road unfortunately. Wont hold 80km/h on long slight hills, has improved down low a bit but haven't been offroad as yet.

I switch between 31" and 35" tyres. All dyno figures are on 35s.
Posts: 28
Joined: Mon Jun 07, 2004 11:01 pm
Location: Tattendorf, Austria (EU)

Post by Gerhard »

Some may come from high friction in the completely rebuilt engine. All parts are brandnew, so give it a little time, my 2L-T diesel engine needed 30.000kms after the rebuild to make me feel that this is not completely crap what I did.
Posts: 357
Joined: Fri Nov 07, 2003 3:30 am
Location: Mount Beauty

Post by Trusa »

For those interested, compression test was fine, tappets adjusted and a f$@ked rear diff diagnosed as draining power. Hasn't been dynoed since new diff, but a lot better. Towed a troopy along the hume at between 85 and 100 km/h (except the big hill just passed glenrowan of course) for 2 hours and ran perfectly. Unfortunately I was expecting too much and the engine is soon to be for sale. Engine turned out pretty good, but for what it's cost me it wasn't worth it. Engine work, turbo cost and tuning totalling just over $16000. That's over a years wage for me and I need some money back. See for sale section soon, will be going for less than half that amount.

Thanks to those who helped! :cool:

Ben
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest