Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Wheel bearings
Moderator: Micka
Wheel bearings
I own a 97 disco and a 97 defender with minor mods. Both of my vechicles seem to chew out wheel bearing continuously for no apparent reasons, has anyone had similar problems or be able to shed some light on the subject for me. Thanks.
Little old patrol with a little old diesel. Driven once a week to church, never been offroad.
I promise.
I promise.
Wheel Bearings
I'm running 32'' tyres on both vechicles with standard offset rims the vechicles are serviced every 5k but the bearings are going in between services the bearings are checked at every service because of this problem. The vechicles do a ratio of 60% offroard to 40% onroad, do you think this may have an affect on the bearings
Little old patrol with a little old diesel. Driven once a week to church, never been offroad.
I promise.
I promise.
i would be getting my vehicle serviced elsewhere if the mechanic you use cannot sort the problem out...
my initial thoughts would be that they are overtightening them..
another thing to consider is to run oil in the bearings as apposed to the grease that LR recommend... but even still, you should not be going through bearings at that rate...
my initial thoughts would be that they are overtightening them..
another thing to consider is to run oil in the bearings as apposed to the grease that LR recommend... but even still, you should not be going through bearings at that rate...
You have a Serious Issue mate!!!
they must be overtighterning them.
I would suggest making it so that the oil from the diff and swivel housings are lubricating them.
The defender and disco have a different hub to the RR's. the bearings are much closer together which means they are effected by heat more as they so close together.
I had second hand disco hubs ones in the rear of my RR for 10 000kms and no problems, I did make sure that the oil seal wasn't there (in the back of the stub axle) so that they were lubed in oil.
they must be overtighterning them.
I would suggest making it so that the oil from the diff and swivel housings are lubricating them.
The defender and disco have a different hub to the RR's. the bearings are much closer together which means they are effected by heat more as they so close together.
I had second hand disco hubs ones in the rear of my RR for 10 000kms and no problems, I did make sure that the oil seal wasn't there (in the back of the stub axle) so that they were lubed in oil.
[i]DAS[/i]
MY05 4.4L V8 Range Rover Vogue
Series 2a Buggy....In the Building
MY05 4.4L V8 Range Rover Vogue
Series 2a Buggy....In the Building
You will probably find your stub axles are damaged where the hub seal seats. The single lip seals let water in easy enough when in good condition, let alone when chewed up by a crappy stub axle.
As said before pull the inner seals out and swap to double lip hub seals.
And either get new stub axles or speedy sleeve them.
As said before pull the inner seals out and swap to double lip hub seals.
And either get new stub axles or speedy sleeve them.
John D
Defender 110 2.4
Defender 110 2.4
Chewing out wheel bearings- not good 
Like many suggested here, may be time to look at another workshop to have your servicing done. I've had 4 Rangies and never had to replace wheel berarings. I do try to check them every few months or so hence why I've never had any issues at all I guess
Either that or time for DIY. Good luck with it.
Trav
Like many suggested here, may be time to look at another workshop to have your servicing done. I've had 4 Rangies and never had to replace wheel berarings. I do try to check them every few months or so hence why I've never had any issues at all I guess
Either that or time for DIY. Good luck with it.
Trav
Land Rover- The Collingwood of 4WD's!!!!
Who is online
Users browsing this forum: No registered users and 0 guests