I fitted 36*12.5-15 ETII on my disco on 15*8 American Racing wheel which offer 31/2" backspacing....The ET"II however have an overall width of 13.2" which limited my steering a lot it is pain in the ass to parallel park this truck or manouever in tight ditches....
Are any after maket 15*8 with more backspacing...15*10 might result in tyre coming off at low pressure
I do not want to go with wheel spacer as they tend to damage wheel bearings....
Looking foward for any helpful feedback
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
15*8 or 15*10 for 36*12.5-15 ET II
Moderator: Micka
15*8 or 15*10 for 36*12.5-15 ET II
96 Disco Gamel Trophy 36"*12.5 ET'II's, F&R ARB's,4.75 R&P GBR,GBR F&R
83 Rangie 2" OME Still Stock
83 Rangie 2" OME Still Stock
I know this guy in Lebanon that has 15x10" rims with MASSIVE offset and hyfro assist steering and he has NO issues with bigger tires 
...
+ he's getting weld-on beadlocks in June
You should listen to him, give him a call
...
+ he's getting weld-on beadlocks in June
You should listen to him, give him a call
LR Disco truggy:
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
Jay,
You need less back spacing, not more, to get the tyre further away from the radius arm.
As far as damage to wheel bearings caused by wheel spacers. The load on the bearings is, in part, determined by the offset of the wheel. But if the same offset is achieved by using wheel spacers, or by offsetting the rim by changing the backspacing, then the effect on the bearing load will be exactly the same.
Personally I would change the wheel backspacing rather than use spacers, but this preference is because I don't like how the forces are transferred through the wheel studs. However people do use them with success, so my concerns my be unfounded.
You need less back spacing, not more, to get the tyre further away from the radius arm.
As far as damage to wheel bearings caused by wheel spacers. The load on the bearings is, in part, determined by the offset of the wheel. But if the same offset is achieved by using wheel spacers, or by offsetting the rim by changing the backspacing, then the effect on the bearing load will be exactly the same.
Personally I would change the wheel backspacing rather than use spacers, but this preference is because I don't like how the forces are transferred through the wheel studs. However people do use them with success, so my concerns my be unfounded.
John
Who is online
Users browsing this forum: No registered users and 0 guests