Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
bodylift question
bodylift question
Im in the middle of a bodylift, do i need to cut an access hole in floor of zook to access top of bolt holding body to chassis.
Its a SWB WT.
Ta
Its a SWB WT.
Ta
It depends what your using for the BL.
Most guys just use the existing studs. I just cut them down, tapped thread all the way up the stud and bolted on my BL block. Then just feed another bolt up from the bottom to hold to chassis, use plenty spring washers.
Most guys just use the existing studs. I just cut them down, tapped thread all the way up the stud and bolted on my BL block. Then just feed another bolt up from the bottom to hold to chassis, use plenty spring washers.
'89' Sierra Softy, 31x10.5M/T's, 2" susp, 2" BL, shackles, extractors.
best not to cut floor, as it weakens structure and won't pass engineer or rwc. If thats an issue.
It does depend on type of bl.
Mine is box section steel, so I bolted top to body and bottom to chassis, just on those captive bolts.
threaded blocks is best idea on those pesky bolts, I think.
I do like NUGGS forementioned idea, too.
christover
It does depend on type of bl.
Mine is box section steel, so I bolted top to body and bottom to chassis, just on those captive bolts.
threaded blocks is best idea on those pesky bolts, I think.
I do like NUGGS forementioned idea, too.
christover
4WD SUZUKI CLUB VICTORIA
http://www.vic.suzuki4wd.com/forum/
http://www.vic.suzuki4wd.com/forum/
thats okKaos wrote:Im using 3" 50mm solid aluminium bar. Its too late to thread the blocks as i just drilled 10mm holes through them at work today.
I wasnt thinking of cutting whole floor, just a small maybe 20mm hole above where the top of the bolt should be.
What do you lot think?
you can make a stud extention if your going with 3 inch bod lift
use some 15mm solid bar and get the upper half of it tapped to m12 1.25 that will bolt to your studs then from the bottom machine it down to make like a bolt on the bottom and tap that to th thread u want
TOYZUKI 96 coily zook,lux diffs, 3 inch suspension lift,3 inch body lift, 33'sMTRS,series 4 hopper,power steer,twin air lockers,4 LINK front and rear,2 inch spacers(GOT WIDTH)
Not too late.
You should have done your homework before attempting this. Even if you scrap the drilled blocks it is a lot cheaper than cutting holes which will make the vehicle unable to be engineered and unroadworthy (read worthless).
Bodylifts is a topic which has been covered at length previously many times, a read of the Sierra bible or a simple search is your next and most important thing to do.
If you are stuck and considering cutting out the four captive bolts which protrude downwards from the floor just behind the front seats, because they do not reach through the chassis now that the lift blocks are in place at either end. Use the blocks you have already drilled. You will need to redrill the centre to house an internally threaded bolt (available through a speciality fastening shop, go the Yellow Pages) You need an internal thread to fit the studs, by memory they are only threaded about 35mm so the internally threaded bolt only needs to be about 45mm. Also by memory the new hole through the block will need to be 15mm to house the internal thread bolt snuggly. But obviously you will measure up everything on your vehicle.
Good idea for future mods. Ask lots of dumb questions on here first. There are some very experienced Zookers on this forum and we don't flame newbies or laugh at those who devise difficult ways to go about doing what everyone else has done simply in the past.
You should have done your homework before attempting this. Even if you scrap the drilled blocks it is a lot cheaper than cutting holes which will make the vehicle unable to be engineered and unroadworthy (read worthless).
Bodylifts is a topic which has been covered at length previously many times, a read of the Sierra bible or a simple search is your next and most important thing to do.
If you are stuck and considering cutting out the four captive bolts which protrude downwards from the floor just behind the front seats, because they do not reach through the chassis now that the lift blocks are in place at either end. Use the blocks you have already drilled. You will need to redrill the centre to house an internally threaded bolt (available through a speciality fastening shop, go the Yellow Pages) You need an internal thread to fit the studs, by memory they are only threaded about 35mm so the internally threaded bolt only needs to be about 45mm. Also by memory the new hole through the block will need to be 15mm to house the internal thread bolt snuggly. But obviously you will measure up everything on your vehicle.
Good idea for future mods. Ask lots of dumb questions on here first. There are some very experienced Zookers on this forum and we don't flame newbies or laugh at those who devise difficult ways to go about doing what everyone else has done simply in the past.
'89 SWB Soft Top, 6.5:1 Calmini gears, rear Lockright, 31s, pwr steering. 1.3 16vmpfi 1300 going in
RB zook wrote:thats okKaos wrote:Im using 3" 50mm solid aluminium bar. Its too late to thread the blocks as i just drilled 10mm holes through them at work today.
I wasnt thinking of cutting whole floor, just a small maybe 20mm hole above where the top of the bolt should be.
What do you lot think?
you can make a stud extention if your going with 3 inch bod lift
use some 15mm solid bar and get the upper half of it tapped to m12 1.25 that will bolt to your studs then from the bottom machine it down to make like a bolt on the bottom and tap that to th thread u want
thought sierras were M10x 1.25 All 3 of mine are
[url]www.twinstickoffroad.com[/url]
Hey Kaos,
Id go with the idea of scrapping the blocks u have and getting then re-made, so u can thread them, The top of the studs are flat and are welded pretty good to the body, Iv tryed to drill them out for a buggy i was building... Either get threaded blocks or Blocks.
Pazz
Id go with the idea of scrapping the blocks u have and getting then re-made, so u can thread them, The top of the studs are flat and are welded pretty good to the body, Iv tryed to drill them out for a buggy i was building... Either get threaded blocks or Blocks.
Pazz
chicks dig panel damage
In my opinion, 2 inch is a much easier option. Apart from the blocks, you wont have to make any other major mods. I did a 2" and got away with just a bit of fiddling, but I reckon with a 3" I would have had to make a new fuel filler hose, mods to brake lines, and extensions to the heater hoses, engine bay wiring, number plate light wiring etc. etc. Besides, I reckon a 3" BL wouldn't get you any major advantages in tyre size, as even with a 2" the size of the wheel well limits tyre size. Of course if you're going to go to town on the inner guards, well now, thats a whole other ball game.
3 inch wasnt all that different
my filler was long enough didnt need extended break lines
the heater hoses are alrite
just a few things to play roung with.
go 2 inch if you have to body lift
im takin my 3 inch body lift out as i dont want or need it
my filler was long enough didnt need extended break lines
the heater hoses are alrite
just a few things to play roung with.
go 2 inch if you have to body lift
im takin my 3 inch body lift out as i dont want or need it
TOYZUKI 96 coily zook,lux diffs, 3 inch suspension lift,3 inch body lift, 33'sMTRS,series 4 hopper,power steer,twin air lockers,4 LINK front and rear,2 inch spacers(GOT WIDTH)
I have a question before i start drilling, im going to drill the old bolts out and install new high tensile items. Im just wondering, for the 10mm captive bolt in the body, it has a 16mm or so head on it thats welded in, if i drill this out to 16mm and install a new 10mm bolt with washer, wont this still slop round in hole?
If so i was thinking of welding a small piece of 4mm metal with a 10mm hole in it under the body where the drilled out 16mm hole is, so it doesnt slop. Would that work?
Is this the location of one of the four rear bolts? Is that the actual head of the bolt showing?
Is this the location of one of the outer of four bolts just behind this small lip in the inner wheelarch? If so where exactly along the lip?
Here is what i was talking about, the 16mm or so head that i need to drill. Ignore the bloody mess of drilling, the bloody holesaw slipped and i had to do a patchie.
If so i was thinking of welding a small piece of 4mm metal with a 10mm hole in it under the body where the drilled out 16mm hole is, so it doesnt slop. Would that work?
Is this the location of one of the four rear bolts? Is that the actual head of the bolt showing?
Is this the location of one of the outer of four bolts just behind this small lip in the inner wheelarch? If so where exactly along the lip?
Here is what i was talking about, the 16mm or so head that i need to drill. Ignore the bloody mess of drilling, the bloody holesaw slipped and i had to do a patchie.
Well i dont have a drain plug there and mine is NT so maybe there is a different location betwen models??? But i didn't have to go through that metal lump to get through to the block and onto metal lift beam the block sits on.
I can't take a pic atm of mine but on monday i can (sister has camera in sydney :/)
I can't take a pic atm of mine but on monday i can (sister has camera in sydney :/)
I have recently done what your in the middle of doing. I used a 16mm holesaw to drill out the captive studs, keeping it cool and lubed up with sum wd-40 at the same time. I did them from the top like you plan to do. I then welded in a small piece of 4mm steel in with a 12.5 mm hole in it, so the bolt wouldnt slop around. Then i used 6- m12 120mm high tensile bolts to tie it all up, with nylock nuts and spring washers. Seemed to work ok.
Emu
Emu
You do not have the required permissions to view the files attached to this post.
Who is online
Users browsing this forum: No registered users and 1 guest