Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

winch q

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 1279
Joined: Wed Jul 28, 2004 9:49 pm
Location: IN THE SHED

winch q

Post by GOT MUD »

did a search and found this http://www.outerlimits4x4.com/PHP_Modul ... hp?t=48959 which is what i want to know about but the thread doesnt really give much detail does anyone else have anymore in put my bar is a std nissan type found on most mqs the only other prob i might have is that ive moved the bar up to sit on top of the chassis rails to suit 2inch body lift the bar is bolted to the rails using plates by the way its all steel bar and plates cheers
PUT YOUR HANDS UP IF YOU WANT TO GO FASTER
RTD Racing
OFFROAD CARTEL
Top
Posts: 510
Joined: Fri Mar 26, 2004 7:58 pm
Location: vic

Contact:
Contact mudtoy

Post by mudtoy »

Without knowing exact measurements/dimensions of your available space...

rule is to ensure winch is bolted to chasis (a winch bar is designed to extend the chasis to give the required support). Winch cradles are available commercially or you could construct one yourself (if you can weld, etc).

The bar can be cut and drilled to support the rollers but nothing else.
www.4wdtv.com.au
SPOA FJ40, 400hp stroker, ARB locked x2, Silverstones, Superwinch, Narva lights, EFS springs, 1284 RTI...
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

Here's one I prepared earlier just for you :lol:

allows for a 3" body lift on an MQ using the std nissan bullbar....
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

the "after effects " of a close encounter with the angle grinder and oxy....
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

The new bottom bits .....

3mm plate was pressed up for the outer "wings" while I used 6mm plate for the centre section......
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

New verticle plates were then cut n fitted and the centre section was then added.....

Verticle plates are from 6mm also.
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

after the "basic bullbar" was done I simply rewelded the orginal tube wrok back on....... done !

this is it finished n fitted.....
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

pics of the actual winch mounting ...... ( WARN 9000lb low mount )
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

again
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

again
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
User avatar
V8Patrol
God of Magnificant Ideas!
Posts: 6774
Joined: Mon Aug 04, 2003 11:22 am
Location: Balls Deep

Post by V8Patrol »

problem is......

I now have & want to fit an 8000lb high mount in the front :bad-words:

so.....

the 9000lb will eventually go on the back bar .......... one day :roll:

Kingy

added to the book of winches ;)
You do not have the required permissions to view the files attached to this post.
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Top
Posts: 1279
Joined: Wed Jul 28, 2004 9:49 pm
Location: IN THE SHED

Post by GOT MUD »

thanks for the replys people its something to think about i might get a winch and start from there ill have a bloody 24v one as it a 24v truck
god i hate 24v :bad-words:
PUT YOUR HANDS UP IF YOU WANT TO GO FASTER
RTD Racing
OFFROAD CARTEL
Top
Posts: 1284
Joined: Tue Mar 22, 2005 12:31 pm
Location: forest lake BUILDING BOOTYFAB BARWORK

Post by frp88 »

why do you hate 24v put a 12v winch and see the extra speed just dont run it to long :D
LETS GO BRONCOS
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 1 guest