Hey Gang!
Was driving home the other day when I heard the worst
sound coming from my transfer case, it got louder and louder and louder!!!
I finally got the Zook home, and emptied the contents of my case to find 2 things
a) No oil
b) The tiny bit of oil that was in there, slurpped out 6 teeth and a shit load of shavings.
Further investigation found that she spat a gear!
Now for my question...
Is it posible to fix a gear in a Rockcrawler or is it a write off and better to go by a whole new kit???
Any help appreciated guys!
Kaz
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
HELP!!! I b roke my Rockcrawler!!!
HELP!!! I b roke my Rockcrawler!!!
Go the Zooks!
www.suzuki4wd.com.au
www.sydney4x4.tk
www.suzuki4wd.com.au
www.sydney4x4.tk
Once you've stripped teeth, the whole gear set usually has to be replaced as well as the bearings, countershaft, etc.
The original "manufacturer" (not seller) of Rockhopper Series 3, Newvale Engineering is in Bessemer St, Blacktown. They maybe able to help you further to advise if it is repairable, but more than likely it won't be.
If you get another gear set, would recommend keeping oil topped up in the T/F case, they work a little better that way.
The original "manufacturer" (not seller) of Rockhopper Series 3, Newvale Engineering is in Bessemer St, Blacktown. They maybe able to help you further to advise if it is repairable, but more than likely it won't be.
If you get another gear set, would recommend keeping oil topped up in the T/F case, they work a little better that way.
http://stores.shop.ebay.com.au/4wd-products
Do you have a contact number or do they have a website for the guy in Blacktown?
As for the oil, I bought the car Sunday, it broke down Monday, was booked for a service Tesday... Hows luck??? ha ha
Kaz
As for the oil, I bought the car Sunday, it broke down Monday, was booked for a service Tesday... Hows luck??? ha ha
Kaz
Last edited by KCZ00K on Wed Aug 17, 2005 2:57 pm, edited 1 time in total.
Go the Zooks!
www.suzuki4wd.com.au
www.sydney4x4.tk
www.suzuki4wd.com.au
www.sydney4x4.tk
arnt they made in america?Podge wrote: The original "manufacturer" (not seller) of Rockhopper Series 3, Newvale Engineering is in Bessemer St, Blacktown. They maybe able to help you further to advise if it is repairable, but more than likely it won't be.
i lack of oil will usually destroy gears. no matter how great they are.
that sux considering you just bought the car
arnt they made in america?Podge wrote: The original "manufacturer" (not seller) of Rockhopper Series 3, Newvale Engineering is in Bessemer St, Blacktown. They maybe able to help you further to advise if it is repairable, but more than likely it won't be.
No, Rockhopper was never made in America. The US brands might be but not Rockhopper.
http://stores.shop.ebay.com.au/4wd-products
For all those that don't know or to those who did and didn't say anything, Rockcrawler gears can be fixed for almost nothing of the price it would cost to replace the whole set!
I sent the gear to an engineering company local to me, who specialise in performance gears for racing and rally suburus. I got it back after 3 days, shoved it back in, gave the case a full clean out, checked bearings AND put a litre of oil in it! I took it for a fanging through menai yesterday without a drama!
I sent the gear to an engineering company local to me, who specialise in performance gears for racing and rally suburus. I got it back after 3 days, shoved it back in, gave the case a full clean out, checked bearings AND put a litre of oil in it! I took it for a fanging through menai yesterday without a drama!
Go the Zooks!
www.suzuki4wd.com.au
www.sydney4x4.tk
www.suzuki4wd.com.au
www.sydney4x4.tk
All but about 20 teeth were smashed, was lucky it didnt do much damage to the other gears and bearing, took a tooth off my smallest gear but i didn't repair that one.
I tried to add a pic to show everyone but the page kept crashing....
The guy made a templet of the whole gear then sent it to his mate that cuts the teeth in. It took about 3 days and he reckons the gear he made is much stronger material than the gear that broke!
I can imagine the next time I break something in there, it will be the only gear left standing ha ha Gawd I hope not!
I tried to add a pic to show everyone but the page kept crashing....
The guy made a templet of the whole gear then sent it to his mate that cuts the teeth in. It took about 3 days and he reckons the gear he made is much stronger material than the gear that broke!
I can imagine the next time I break something in there, it will be the only gear left standing ha ha Gawd I hope not!
Go the Zooks!
www.suzuki4wd.com.au
www.sydney4x4.tk
www.suzuki4wd.com.au
www.sydney4x4.tk
stephen wrote:Great news. Post up the vendor? there might be a few people on the board that will benefit from them.
and tell him to keep the template
TOYZUKI 96 coily zook,lux diffs, 3 inch suspension lift,3 inch body lift, 33'sMTRS,series 4 hopper,power steer,twin air lockers,4 LINK front and rear,2 inch spacers(GOT WIDTH)
How much of that gear did they Re-Make? How much did they Charge you? Did they just cut the large gear off and remake it and weld a new one on or did they re-make the entire gear set?KCZ00K wrote:For all those that don't know or to those who did and didn't say anything, Rockcrawler gears can be fixed for almost nothing of the price it would cost to replace the whole set!
I sent the gear to an engineering company local to me, who specialise in performance gears for racing and rally suburus. I got it back after 3 days, shoved it back in, gave the case a full clean out, checked bearings AND put a litre of oil in it! I took it for a fanging through menai yesterday without a drama!
I'm keen to learn more as to the Co. that did the work. I have a broken Rockhopper or three in my collection (I think that I have a Series 1 and 3 there). I might be able to get them rejuvenated for future use, maybe even get the bloke that did yours to do the testing on them for OL members to know what the problem is as to why they break.
Was the counter gear the only damaged gear or was the input and output gears damaged also?
Just having a look at the broken gear in the pic on your site, looks like some heat went through that counter gear.
Was the counter gear the only damaged gear or was the input and output gears damaged also?
Just having a look at the broken gear in the pic on your site, looks like some heat went through that counter gear.
http://stores.shop.ebay.com.au/4wd-products
I gave the gear to an engineering company called CNB Engineering, they didn't fix the broken gear he made a brand new one, most engineering companys can do that, but then he sent it to another company to cut the gears, and thats the peoples names I am yet to find out. The guy that made the gear is my fiances friend so we didn't pay full price but i will find out how much a full charge is. I know it isnt alot....
Another place that were keen to do it, and they do everything in their factory, was Par engineering in Minto Campbelltown, they also do high performance gears, but I heard they weren't that good, but I also know a few people who have done quite a bit of business with them and their cars are still going, so make your own decision.
http://www.par-engineering.com/
In my case, only the one gear broke, but chipped 2 teeth on my smallest cog. You are right with the amount of heat, a case running with no oil!!
Im planning another trip soon so that will be the decider as to how well the gear is made, so far it has travelled well on roads and off roads so its looking good.
Sorry I haven't got anymore info for you guys, my fiance took care of the repairs, but as soon as i find out more I will definately post it!!
Kaz
Another place that were keen to do it, and they do everything in their factory, was Par engineering in Minto Campbelltown, they also do high performance gears, but I heard they weren't that good, but I also know a few people who have done quite a bit of business with them and their cars are still going, so make your own decision.
http://www.par-engineering.com/
In my case, only the one gear broke, but chipped 2 teeth on my smallest cog. You are right with the amount of heat, a case running with no oil!!
Im planning another trip soon so that will be the decider as to how well the gear is made, so far it has travelled well on roads and off roads so its looking good.
Sorry I haven't got anymore info for you guys, my fiance took care of the repairs, but as soon as i find out more I will definately post it!!
Kaz
Go the Zooks!
www.suzuki4wd.com.au
www.sydney4x4.tk
www.suzuki4wd.com.au
www.sydney4x4.tk
The large gear is released by a pin, its kinda like 2 peices, so when it was released, its was just a flat cog.RUFF wrote:How much of that gear did they Re-Make? How much did they Charge you? Did they just cut the large gear off and remake it and weld a new one on or did they re-make the entire gear set?
Go the Zooks!
www.suzuki4wd.com.au
www.sydney4x4.tk
www.suzuki4wd.com.au
www.sydney4x4.tk
i no why the series 1 were breaking, i checked this out my self, because they r a 2 piece gear, they were not assembeled properly, and had a large about of runout, causing noisy gears and fatigue over time. as for the series 3 im 100% sure it comes down to heat treating, material and finish or profile of teeth.
Who is online
Users browsing this forum: No registered users and 45 guests