trying to decide on diffs for buggy and am looking at either GU, built dana 44 or dana 60s but cannot make up my mind so any help would be great. i am leaning towards GU but would like to know strength differences.
cheers
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
DANA v GU !!!
Moderators: toaddog, TWISTY, V8Patrol, Moderators
there was a thread on here a while ago, i searched for it but couldnt find it. One of the replys was from stragerover (im preety sure it was anyway), it gave the specs on each diff and on paper the GU diffs are the one to buy (H260 rear). im not sure of which models came with the H260, but i can tell you leaf sprung rear diffs are all H260 and full floating. some 3L tubo diesels got them too. i have no spec on the dana for comparison though.........
good luck with the buggy
good luck with the buggy
Not saying the D60`s aren`t any good but cheezy mav runs GU diffs and even though we tried to break them we never did. At TTC05 the rear pinion only broke because the broken controll arm let the diff rotate to the point where the tail shaft uni was locked. Even a D60 would break a pinion in this case. We also never broke a CV. We also tried this many times and with 42`s aired down to about 2, his chev singing big time at about 7500rpm and slamming the side walls in to a rock bigger then the 42`s over and over and over again. The tyre was getting traction as it hit the rock and the tyre would twist up on the rim untill it couldn`t twist anymore then it would let got of the byte it had. If I hadn`t of see this with my own eyes would have never said that GU diffs are strong. I think you`d be very surprised at how strong they are POS.POS wrote:Yeah, the GU is the go!
Who are you farken kidding.
Stock Dana 60 you could wheel all season in WEROCK and not break them, do that with a GU nissan and you'd be lucky to finish a few stages.
I wouldn't even be comparing the two!!!!
Yes a built D60 would be WAY stronger but as far as stock goes I don`t think they`d walk all over a GU diff.
Last edited by MissDrew on Tue Dec 13, 2005 8:03 pm, edited 1 time in total.
ok, from the way i see it d60's have more aftermarket gear than any other diff(in the USA)
i have a sals 8ha in the rear of my def110, these are very similar to a d60, they have a cast centre section with the axle tubes inserted into this.
i don't know much about the gu's but if they are like a rover/lux diff they would be easier to laminate.
does anyone make bigger axles out of 300m etc for nissans. a cromo cv for them would also be good.
it would be good if more guys in oz ran the gu's to open up the aftermarket gear for them. as building up a comp 60, though proven, would be costly
but hey i'm still on 32's so my sals will be just fine
serg
i have a sals 8ha in the rear of my def110, these are very similar to a d60, they have a cast centre section with the axle tubes inserted into this.
i don't know much about the gu's but if they are like a rover/lux diff they would be easier to laminate.
does anyone make bigger axles out of 300m etc for nissans. a cromo cv for them would also be good.
it would be good if more guys in oz ran the gu's to open up the aftermarket gear for them. as building up a comp 60, though proven, would be costly
but hey i'm still on 32's so my sals will be just fine
serg
Im with the GU for availability and weight(light i mean), and they are strong, I think they would be fine if the centre was shaved and you didnt go over the top with tyre size.
Mock
Mock
My photographic Art http://www.redbubble.com/people/ljxtreem
www.dirtcomp.com.au
Sierrajim wrote:
So hurry up, come back, buy a Lada (can't believe i just said that) and we'll go wheelin'.
www.dirtcomp.com.au
Sierrajim wrote:
So hurry up, come back, buy a Lada (can't believe i just said that) and we'll go wheelin'.
Don't know enough about the dana's but you are kidding rightPOS wrote:you could wheel all season in WEROCK and not break them, do that with a GU nissan and you'd be lucky to finish a few stages.
You don't think a GU diff (be it front or rear) would last a few stages in WEROCK or similar Cheers
Linc
[quote="chimpboy"]Punctuation is the difference between 'I helped my Uncle Jack off his horse' and 'I helped my uncle jack off his horse.'[/quote]
Linc
[quote="chimpboy"]Punctuation is the difference between 'I helped my Uncle Jack off his horse' and 'I helped my uncle jack off his horse.'[/quote]
POS wrote:Yeah, the GU is the go!
Who are you farken kidding.
Stock Dana 60 you could wheel all season in WEROCK and not break them, do that with a GU nissan and you'd be lucky to finish a few stages.
I wouldn't even be comparing the two!!!!
I really hope you are only having a go at serting people up Adrian which I know you do do. Because if you do truely belive this then you have just lost alot of credit in my book. Mainly with the lucky to finish a few stages line. Shit I`m going to be running GQ diffs under my buggy and they are weaker then the GU diffs, so what are we going to bet that I can finish more then a few stages on GQ diffs
...
If you are gonna go danas 60's... Go the Hi-Pinion Rockcrusher Dana 60's . Whats money.. 
Go the GU's man.. As guts was saying... After watching mr. cheeseman drive that mav of his at a few comps on 42's !!!! I can attest to the strength of these diffs.
There was a thread here a few months ago that had a picture comparison of a dana 60 v gu v 80 series axles and then the last 2 had cv's compared.
I have searched and can't find it for the life of me...
. Whats money.. Go the GU's man.. As guts was saying... After watching mr. cheeseman drive that mav of his at a few comps on 42's !!!! I can attest to the strength of these diffs.
There was a thread here a few months ago that had a picture comparison of a dana 60 v gu v 80 series axles and then the last 2 had cv's compared.
I have searched and can't find it for the life of me...
[quote="MSCHIF"]SPUA its like shaving a barbie dolls head, amusing but pointless.[/quote]
He will only be kidding Dave............surely. If not then he does not have the knowledge that I thought he had. I'm sure even Sam and Tony would agree that it is very possible to compete at WEROCK and the likes on GQ diffs let alone GU diffs................if not Adrian then how do those certain people do it on anything less then a dana 60..............
Cheers
Linc
[quote="chimpboy"]Punctuation is the difference between 'I helped my Uncle Jack off his horse' and 'I helped my uncle jack off his horse.'[/quote]
Linc
[quote="chimpboy"]Punctuation is the difference between 'I helped my Uncle Jack off his horse' and 'I helped my uncle jack off his horse.'[/quote]
BIG GQ wrote:He will only be kidding Dave............surely. If not then he does not have the knowledge that I thought he had. I'm sure even Sam and Tony would agree that it is very possible to compete at WEROCK and the likes on GQ diffs let alone GU diffs................if not Adrian then how do those certain people do it on anything less then a dana 60..............
Agreed 100%. Shit he does it on 60 series diffs, maybe its just got to have 60 in it to be good enough to finsh a few stages of werock
As does Tom. You are right..............just needs to have 60 in there somewhere................so Dave ditch the idea of GQ diffs and don't stuff around with GU diffs............................Guts wrote: Shit he does it on 60 series diffs,
Go straight to the G60 patrol diffs
Cheers
Linc
[quote="chimpboy"]Punctuation is the difference between 'I helped my Uncle Jack off his horse' and 'I helped my uncle jack off his horse.'[/quote]
Linc
[quote="chimpboy"]Punctuation is the difference between 'I helped my Uncle Jack off his horse' and 'I helped my uncle jack off his horse.'[/quote]
Firstly, I know Jack Sheet about these bits. But I was under the impression that the GU, despite having a big CV, the outer axle was the same as any other Toy/Nissan outer, and probably ultimately the limiting factor for that axle rather than the inners, actual CV or CW/P. How does this compare to the D60?
LOL! It's only somebody elses money. Get a Rangie axle. 
LOL! It's only somebody elses money.
Get a Rangie axle. Cheers
Slunnie
Discovery TD5, Landy IIa V8 ute.
Slunnie
Discovery TD5, Landy IIa V8 ute.
GU's are just about to take a BIG jump in after market bits,
BIG axles, BIG uni's ect ect.
D60's are strong cos of the after market bits you can get.
To date the Dana is stronger, but things are about to change.
In the new year we will have all the good bits for the GU for sale.
BIG axles, BIG uni's ect ect.
D60's are strong cos of the after market bits you can get.
To date the Dana is stronger, but things are about to change.
In the new year we will have all the good bits for the GU for sale.
NOW ABLE TOO SAY WHAT I WANT WITHOUT FEAR OF LOOSING SALES.
The person who says it cannot be done should not interrupt the person doing it.
The person who says it cannot be done should not interrupt the person doing it.
Until sombody can fit a 35 spline axle through into a nissan hub a nissan axle will never be anywhere as strong as a half built dana 60.
A nissan GU front axle has a very small stub shaft and I dont care who reckons what about how hard they drive. If you got a GU front axle and you carnt break the small stub shaft then you arnt trying very hard. A GU stub is something like 31 spline and 1.31in diameter - which is tiny compared to dana 60 stuff.
Sam
A nissan GU front axle has a very small stub shaft and I dont care who reckons what about how hard they drive. If you got a GU front axle and you carnt break the small stub shaft then you arnt trying very hard. A GU stub is something like 31 spline and 1.31in diameter - which is tiny compared to dana 60 stuff.
Sam
OK i was elaborating the example of the GU's been only able to last a few stages. They would be lucky to finish one stage!
BUT the question is asking in a arse about way what is stronger!
And the fact is a STOCK Dana 60 is stronger than a stock GU.
Thats a Fact, no if and or buts.
If you were to start a season with Stock Dana 60 gear then you would more than likely complete all 5 rounds of WEROCK (just using that as an example). If you attempted this with Gu's than i would be not as confident.
No point squabling over "he said this and he said that" at the end of the day Dana 60 is stronger than GU.
Also BIG GQ if i said that 60 series diffs are stronger than GQ i am sure we wouldn't hear the end of it, surely nothing could be better than Nissan Diffs.
But hey beleive what you want, if you honestly want to believe that GU nissans are stronger than a Dana 60 than thats your opinion. I am not bagging GU diffs just stating that Dana 60's are stronger.
BUT the question is asking in a arse about way what is stronger!
And the fact is a STOCK Dana 60 is stronger than a stock GU.
Thats a Fact, no if and or buts.
If you were to start a season with Stock Dana 60 gear then you would more than likely complete all 5 rounds of WEROCK (just using that as an example). If you attempted this with Gu's than i would be not as confident.
No point squabling over "he said this and he said that" at the end of the day Dana 60 is stronger than GU.
Also BIG GQ if i said that 60 series diffs are stronger than GQ i am sure we wouldn't hear the end of it, surely nothing could be better than Nissan Diffs.
But hey beleive what you want, if you honestly want to believe that GU nissans are stronger than a Dana 60 than thats your opinion. I am not bagging GU diffs just stating that Dana 60's are stronger.
are these the same diffs his buggy ran at ozrock?Guts wrote:Not saying the D60`s aren`t any good but cheezy mav runs GU diffs and even though we tried to break them we never did. At TTC05 the rear pinion only broke because the broken controll arm let the diff rotate to the point where the tail shaft uni was locked. Even a D60 would break a pinion in this case. We also never broke a CV. We also tried this many times and with 42`s aired down to about 2, his chev singing big time at about 7500rpm and slamming the side walls in to a rock bigger then the 42`s over and over and over again. The tyre was getting traction as it hit the rock and the tyre would twist up on the rim untill it couldn`t twist anymore then it would let got of the byte it had. If I hadn`t of see this with my own eyes would have never said that GU diffs are strong. I think you`d be very surprised at how strong they are POS.POS wrote:Yeah, the GU is the go!
Who are you farken kidding.
Stock Dana 60 you could wheel all season in WEROCK and not break them, do that with a GU nissan and you'd be lucky to finish a few stages.
I wouldn't even be comparing the two!!!!
Yes a built D60 would be WAY stronger but as far as stock goes I don`t think they`d walk all over a GU diff.
if so i heard snap crackle pop a couple of times, on a lighter buggy without the "big" motor pushing them
Spit my last breath
Put it this way. You give me a rig with a GU front axle for 10 minutes and I bet I can break a CV. Bind the front tyre in a hole, turn the steering wheel to full lock and drop the clutch at max revs in reverse and I reckon it will break.BIG GQ wrote: Don't know enough about the dana's but you are kidding right
If I gave you the same rig with a built dana 60 in the front I dont think you would break it in a year. A built dana 60 is just that much stronger.
Just check out the US rockcrawling guys with the dana 60 front axles with CTM joints and CTM 300m 35 spline shafts. These guys wheel the crap out of their rigs all year at competitions and wheel even harder in between comps and never break all year. They also have over 150kg of lead shot in each front tyre and they still dont break.
Sam
So what size will the outer stub shaft be?? Carnt see that you can go any bigger than the stock 31 spline through the GU splindle.Cheezy4x4 wrote:GU's are just about to take a BIG jump in after market bits,
BIG axles, BIG uni's ect ect.
D60's are strong cos of the after market bits you can get.
To date the Dana is stronger, but things are about to change.
In the new year we will have all the good bits for the GU for sale.
Sam
Can i ask what the lead shot is for?Strange Rover wrote:Put it this way. You give me a rig with a GU front axle for 10 minutes and I bet I can break a CV. Bind the front tyre in a hole, turn the steering wheel to full lock and drop the clutch at max revs in reverse and I reckon it will break.BIG GQ wrote: Don't know enough about the dana's but you are kidding right
If I gave you the same rig with a built dana 60 in the front I dont think you would break it in a year. A built dana 60 is just that much stronger.
Just check out the US rockcrawling guys with the dana 60 front axles with CTM joints and CTM 300m 35 spline shafts. These guys wheel the crap out of their rigs all year at competitions and wheel even harder in between comps and never break all year. They also have over 150kg of lead shot in each front tyre and they still dont break.
Sam
&
How does it work?
Who is online
Users browsing this forum: No registered users and 60 guests