Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
COILOVERS ON A RANGIE
Moderator: Micka
COILOVERS ON A RANGIE
looking for advice on spring rates and shock settings to fit a set of coilovers to a rangie.theres not many running them where i come from (ireland) so any info would be appreciated.also are some of you guys running toyota or nissan shocks on discos
any info appreciated
thanks
JJ
any info appreciated
thanks
JJ
I did abit of reasearch on pirate and asked afew questions and for slower rock crawling setups I have just got myself a pair of dual rate coilovers.
The rates i got and will be trialing first up is 400lb over 200lb (dual rate as mentioned) This is for the front.
I am not fitting coil overs to the rear but the reaserch was to run 500 over 200.
I beleive Kermit may have sum info on his dual rate setup for high speed style events and its around 500 over 300 (could be wrong)
The rates i got and will be trialing first up is 400lb over 200lb (dual rate as mentioned) This is for the front.
I am not fitting coil overs to the rear but the reaserch was to run 500 over 200.
I beleive Kermit may have sum info on his dual rate setup for high speed style events and its around 500 over 300 (could be wrong)
Dual rate is one of the advantages of coil overs.
You need to determine how much static load (lbs) is carried by each coilover.
And decide how many inches you want the coilover to be compressed at the static ride height (for example 70% of travel). This is how much down travel you will have.
From these numbers you can calculate the 1st spring rate = static load/down travel. This is the combined spring rate of both the upper and lower coils together (note that it is not the sum of both spring rates).
Most people want the spring rate to increase when the coils are compressed a little more than the static load. This point can be adjusted with the nuts that limit the travel of the slider. After the slider is stopped by the nuts, all further compression occurs only in the bottom spring, so this is your 2nd spring rate.
If you plot the spring load against travel you will get a better idea of what will happen.
You need to determine how much static load (lbs) is carried by each coilover.
And decide how many inches you want the coilover to be compressed at the static ride height (for example 70% of travel). This is how much down travel you will have.
From these numbers you can calculate the 1st spring rate = static load/down travel. This is the combined spring rate of both the upper and lower coils together (note that it is not the sum of both spring rates).
Most people want the spring rate to increase when the coils are compressed a little more than the static load. This point can be adjusted with the nuts that limit the travel of the slider. After the slider is stopped by the nuts, all further compression occurs only in the bottom spring, so this is your 2nd spring rate.
If you plot the spring load against travel you will get a better idea of what will happen.
John
james feeney wrote:Eh up Jason, how's things? You done much to tigger since May?
JJ,
What are we doing with a Range Rover??
Those CVs I tried today aint gonna work mate, need to remove too much material.
JF
Tell Steph I was asking for her Jason.
Hey James hows it going mate
Def nextt year for 3 peaks challenge mate
Mal
Eh up Mal,
How's it hunging? How's the knee/ankle/leg?
Three Peaks was a blast this year, I ended up driving the truck for you mate, had a blast. No worries for next year. Our own event, Muddy Truckers Trophy is on first weekend in March if you're at a loose end. It's only 7 months between that and the Three Peaks, I'm sure we could find you something to do.
All the best for the new year and chrimbo
Check out "post up your rovers" or "how many 90's out there" for pics of the truck
How's it hunging? How's the knee/ankle/leg?
Three Peaks was a blast this year, I ended up driving the truck for you mate, had a blast. No worries for next year. Our own event, Muddy Truckers Trophy is on first weekend in March if you're at a loose end. It's only 7 months between that and the Three Peaks, I'm sure we could find you something to do.
All the best for the new year and chrimbo
Check out "post up your rovers" or "how many 90's out there" for pics of the truck
Hey James
Yeah mate knee is healing well very happy with it.
Rebuilding the engine on the truck ATM wll be even quicker also welded plates onto the chassis where it cracked so that is all sorted.Pretty sure this will be my last OBC and am looking for a Navi mate!!! know anyone lol
Have a blast at muddy truckers and sa hello to all the Lads for me
have a great xmas & new year mate
Mal
Yeah mate knee is healing well very happy with it.
Rebuilding the engine on the truck ATM wll be even quicker also welded plates onto the chassis where it cracked so that is all sorted.Pretty sure this will be my last OBC and am looking for a Navi mate!!! know anyone lol
Have a blast at muddy truckers and sa hello to all the Lads for me
have a great xmas & new year mate
Mal
Who is online
Users browsing this forum: No registered users and 3 guests