I've just installed some 6.5:1 gearing in my t-case and it won't engage 4x4. The lever moves through all positions smoothly ie 2h, 4h, 4L. High and low range work but it won't allow drive to the front shaft. The lever moves correctly to engage 4x4 but the problem is that the ring that moves across to allow drive to the front isn't reaching the front shaft. I think there might be a problem with the front shaft part goin into the longer shaft. The reason I believe this is the problem is because I have the internals from a second case here too and when interchanging parts the other parts lead me to believe the bearing located in between these parts ( shown circled in yellow in pic) is what is stopping the other part goin in and therefore not allowing for it to lock into 4x4 because it can’t reach.
In the pic I’ve circled the part in red which is supposed to go into the hole that is circled in yellow. And atm I’m thinking that, that is the problem. I’m gonna try and remove it and change in another bearing this week (I have a severe case of dermatitis on my hands so I can’t work on the car right now) but I’m after any other help or experiences people might have had with cases or any other advise.
Hopefully I can sort it out soon and start wheeling my POS! And hopefully this post makes some sense to others as it’s hard a bit difficult to explain
Cheers, Mark.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Rebuilt x-fer won’t engage 4x4 (how to remove bearing?)
Rebuilt x-fer won’t engage 4x4 (how to remove bearing?)
Last edited by markil on Thu Dec 15, 2005 3:28 pm, edited 1 time in total.
Mark.
I'm not sure which bearings are the detent bearingsnicbeer wrote:was both the detent bearings put in?
i believe there is two of them in there.
cheers
but yes, I beleive all bearings are in there as i copied from the other internals and the instructions that came with the gearing. And i replaced in total 9 bearings i think it was...I was talking to someone about this and they suggested maybe the main shaft was out of alignment, soemthing for me to consider I guess.
Mark.
Mark.
Yep, this is exactly what I'm thinking too. Now I just had a quuick look at it and I don't know how to remove this bearing... can anyone help me here who's done it before?
And I compared the position of that bearign to the one I have on a spare shaft and it has been pushed in further into the shaft
I think this must have happened when I tightened up the bolts on the fornt part of the case. Is there anythign else I should check that might have been forced out of alignment as well?
Mark.
P.S I hate transfer cases
And I compared the position of that bearign to the one I have on a spare shaft and it has been pushed in further into the shaft
I think this must have happened when I tightened up the bolts on the fornt part of the case. Is there anythign else I should check that might have been forced out of alignment as well?Mark.
P.S I hate transfer cases
Mark.
I just took another pic close up of the bearing to better show it. This is just a close up of the same spot as in the other pic where i high lighted it in yellow.
I draw the outer casing and how the pins in the bearing sit as the photo wouldn't come out very clear.
Mark.
I draw the outer casing and how the pins in the bearing sit as the photo wouldn't come out very clear.
Mark.
You do not have the required permissions to view the files attached to this post.
Mark.
ya need sum waxy grease firm yet a bit plyable, a drift thats the same diameter as the hole its goin into. half fill the hole with waxy grease, proceed to hit drift with hammer, this forces the wax under the bearing and hopefully forces the outer of the bearing out. i learnt how to do this of a guy i saw trying to get a bronze spigot bearing out of a crankshaft, worked a treat.
buggy time............
Hmmmm.... sounds interesting, had to read it twice to understand fully, hehe. Might give it a go on the weekend... any reccomdations on what kind of wax to use that has the right plyability? ( i dion't think "plyability" is the word but you know what I meanbazooked wrote:ya need sum waxy grease firm yet a bit plyable, a drift thats the same diameter as the hole its goin into. half fill the hole with waxy grease, proceed to hit drift with hammer, this forces the wax under the bearing and hopefully forces the outer of the bearing out. i learnt how to do this of a guy i saw trying to get a bronze spigot bearing out of a crankshaft, worked a treat.
)Mark.
Mark.
Have u got access to a puller,u might find a spigot bearing puller might work.When i did mine i had no choice except break the cage and get the needles out then i had a engraver with alot of attachments and grind the outer cage away...what a bitch it was as i tryed so hard not to grind any case harding away from the main shaft.Then i used a drift and hit the new bearing in...its been fine since.The attachment was like a small grinding stone in a small dowl kinda looking shape ,then i used some sand paper on another attachment.You can get these things in like Dicksmith i think.Hope this helps
Who is online
Users browsing this forum: No registered users and 86 guests