Where and who does these conversions, I have a spare transfer case so what else do I need becides lenghtening and shortening drive shafts. I beleive its not that hard just need to find a supplier.
Cheers Fathilux
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Twin transfer cases
Moderators: toaddog, Elmo, DUDELUX
Twin transfer cases
Cheers Fathilux,
Gravity becomes heavier when you add Consequence , Brisbane Waters 4wd Club
Gravity becomes heavier when you add Consequence , Brisbane Waters 4wd Club
marks its the best place to get the adapter but its a few $$ to do the conversion properly
Adapter $595
4spd transfer $200 -400
crossmember $400 i think got mine from bubs
speedo cable $32
drive shaft mods $0-500 depending on who ya know and where ya go
cost also depends if you doing it urself or paying somone , ull need some big circlip pliers, a press etc, to assemble the reduction box to the adapter.
All up it took me about 1 day to install + time for driveshaft mods,
now i know what im doing i could prolly knock it over in half a day in a pretty basic workshop.
You'll also need to cut a largeish hole in the floor for the second shift, and dependsing what sort of seats u have and a center console there are some diff ways to do it
i got bucket seats and a 4runner center console, so i made a dog leg shifter so it comes up though the lil bowl infont of the box.
Adapter $595
4spd transfer $200 -400
crossmember $400 i think got mine from bubs
speedo cable $32
drive shaft mods $0-500 depending on who ya know and where ya go
cost also depends if you doing it urself or paying somone , ull need some big circlip pliers, a press etc, to assemble the reduction box to the adapter.
All up it took me about 1 day to install + time for driveshaft mods,
now i know what im doing i could prolly knock it over in half a day in a pretty basic workshop.
You'll also need to cut a largeish hole in the floor for the second shift, and dependsing what sort of seats u have and a center console there are some diff ways to do it
i got bucket seats and a 4runner center console, so i made a dog leg shifter so it comes up though the lil bowl infont of the box.
You do not have the required permissions to view the files attached to this post.
www.overkill4x4.com
ph 94766137
ph 94766137
The Marlin Crawler Adapter kit
Yesterday I had my Marlin Crawler / completely reconditioned gearbox and transfer case fitted into my Hilux, see some photo's so far.
Just a Toyota Hilux 4x4 with a few mods, nothing too extreme.
I have one for sale at the moment.spazbot wrote: 4spd transfer $200 -400
$150 if anyones interested.
ghordern@yahoo.com
I have a brand spanking new Marks dual transfer adaptor with everything in the box except the instruction booklet (I lost it 
there is better instruction on the net anyway) for sale for $495.
Brand new and $100 cheaper than Marks retail.
Paul.
there is better instruction on the net anyway) for sale for $495.Brand new and $100 cheaper than Marks retail.
Paul.
R.I.P Brock Fontanini 28-3-06 - 16-2-08
www.teamcarnage.net
www.teamcarnage.net
Who is online
Users browsing this forum: No registered users and 0 guests