Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

urgent help needed

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 407
Joined: Wed Mar 30, 2005 4:01 pm
Location: browns plains

urgent help needed

Post by Matt_88 »

helpppppp...... how the hell do u get a crankshaft pulley off ur motor? the engine is in the car and we need to change ir to a double pulley but we cant figure out how to get the single pulley off.

we have tried everything we can think of but still havnt been able to get it off.

we have the car in 1st low range and the motor still cranks over.

how can we get it off?

need help urgently cause this car is our only car atm and it needs to be driving tomorrow....


cheers
matt
NECKUPYAPARROT4x4

Tosa_03

Proudly sponsored by and part of:-

Tosa Racing Co.
Top
Posts: 138
Joined: Thu Dec 22, 2005 10:06 pm

Post by baddboy »

Have you un done the bolt?? You will need a set of pullers to get it of the crankshaft.
Top
Posts: 407
Joined: Wed Mar 30, 2005 4:01 pm
Location: browns plains

Post by Matt_88 »

yer soz forgoet to mention. we cant undo the bolt as the pulley/crankshaft spins withh it.
NECKUPYAPARROT4x4

Tosa_03

Proudly sponsored by and part of:-

Tosa Racing Co.
Top
Posts: 138
Joined: Thu Dec 22, 2005 10:06 pm

Post by baddboy »

You need to put a big breaker bar on the nut and position against you chasis. Use the engine cranking over to supply the power to carack the bolt.
Top
Posts: 677
Joined: Mon Nov 18, 2002 10:00 am
Location: Melbourne

Contact:
Contact roly

Post by roly »

or put the car in gear to stop the engine turning
08 340kw HSV Maloo 6.2L
John Roly
Melbourne Again
Top
Posts: 13
Joined: Thu Aug 25, 2005 7:41 pm

Post by mik4x4 »

use a rattle gun :)
Top
Posts: 3299
Joined: Fri Nov 08, 2002 8:28 am
Location: Sydney

Post by spazbot »

take the starter motor off and put a breaker into the teth off the flywheel to brace it as ur mate cracks the nut with a long breaker bar, Short but quick jolts normally gets em undone ok
www.overkill4x4.com
ph 94766137
Top
Posts: 438
Joined: Thu Jun 24, 2004 4:58 pm
Location: wollongong

Post by Stackson45 »

Maybe late, but in HIGHER gear, with mate's foot on brake, and huge breaker bar.

Taller gear means the engine will turn less times per wheel turn.
Landcruiser UTE 1996 FZJ75 - SPOA, 35"s,
extended chassis, poor mans extra cab, 4.56 diff gears, Lockright front, chinese air locker rear...
Top
Posts: 135
Joined: Wed Jul 13, 2005 6:44 pm
Location: Central Coast NSW

nut

Post by Sneddo »

Like baddboy said breaker bar against the chasis just touch the key tho when you give it a crank. Had to do it last week to change water pump once nut was undone to my amazement pully came off by hand :armsup:
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 0 guests