Notice: We request that you don't just set up a new account at this time if you are a previous user. If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
G'day guys.
just bought my first 4wd. a 1978 FJ40 with a 2F on dual fuel. the car has overheating issues which we found out when we started crawling in the bush. no problems on the highway so we did not realise the car boiled a couple of times so we think it could be headgasket.
i don't want this to turn into a project like my brothers 40 which has been in the garage for 4 years!!! If i did a full rebuild i would end up having to strip the block send it away for machining and fill our shed with more parts. i was thinking just pull the head off change the headgasket (if thats the prob) and do the valves. what would a short block in good nick for a 2F worth?
The other option is a VL engine we have sitting at home that is reasonable nick. the only problem is getting a bellhousing to suit. has anyone heard of this conversion into a 40series?
hokey wrote:G'day guys.
just bought my first 4wd. a 1978 FJ40 with a 2F on dual fuel. the car has overheating issues which we found out when we started crawling in the bush. no problems on the highway so we did not realise the car boiled a couple of times so we think it could be headgasket.
i don't want this to turn into a project like my brothers 40 which has been in the garage for 4 years!!! If i did a full rebuild i would end up having to strip the block send it away for machining and fill our shed with more parts. i was thinking just pull the head off change the headgasket (if thats the prob) and do the valves. what would a short block in good nick for a 2F worth?
The other option is a VL engine we have sitting at home that is reasonable nick. the only problem is getting a bellhousing to suit. has anyone heard of this conversion into a 40series?
thanks guys,
Calvin
i honestly don't think the VL motor will have the torque your after, i don't know the numbers, but even if the numbers are close, look at where it's produced in the rev range... a 2f produces lots of torque down low and loves to lug. think about the displacement and stroke difference of the two motors...
anyway, i answered your Q on where to find one in the other post (oh and throw an add up in the wanted section), i wouldn't hesitate to just do a head gasket (get the head pressure tested too) and call it good.
but it might be worth checkin out the rest of your cooling system first. no point throwing another motor in and having the same problem.
yeh we checked the cooling system yesterday and the thermo works we just aren't sure about the radiator. we will take it to a place maybe this arvo and get them to check it out.
gotta love that low down the 2F has i guess it is bigger than a 253 tho. crappy holden V8's but i think i should just rip the head off and do a bit of headwork and leave it at that. i just want it reliable so i am not stuck somewhere waiting for a trailer to come and get me.
Try buying a toyota thermostat
as there has been problems with thermosats from other makers
and dont forget the rubber ring that go's on top of the thermostat
also use coolant not just water
mine gets warm when 4wding but qickly cools down when left to idle
also if you get it tested have them check the gauge to see if it accurate
[quote="RN"]So do you support your local vendor...not if it is going to cost me almost double. [quote]
the thermostat is working and yes it has the rubber ring. the radiator fins are quite bent but i don't think they would make that much difference. will go to the rad place and they will tell us if the system is working. if it is i will assume BHG
hokey wrote:yes but it can also depend on where it is blown. it is blowing a bit of water out the exhaust pipe aswell
When at start up from cold or all the time
most cars have water (condensation) come out the exhaust pipe when first started until up to temp
if its all the time you will get bubbles in the radiator then its a head problem
[quote="RN"]So do you support your local vendor...not if it is going to cost me almost double. [quote]
i'd check the water pump is working, and for piece of mind i'd get a new thermostat, i had one that "worked" when doing the test on them, but still overheated the car. changed it out and it never gets over 1/4 hot now.
nah yes it is the nissan six but i was just saying that it feels better than a V8. nah i would not put a friggin 253 in. the only good V8's are chevs, Hemi's and one holden V8 the 304 and yes the displacement is pretty close.
the car boiled a couple of times so we think it could be headgasket.
i guess it is bigger than a 253 tho. crappy holden V8's 
but i think i should just rip the head off and do a bit of headwork and leave it at that. i just want it reliable so i am not stuck somewhere waiting for a trailer to come and get me.
and yes the displacement is pretty close.