Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
race seats
Moderator: Micka
race seats
has anyone put race seats into their rovers before? i have an old 81 2 door rangie and have a set of race seats to put in. after looking at the original seat bases it looks like a mission and a half! anyone have any pointers on this?
I have 2 Cobra race buckets in mine.
The seat base mounts to 32x32x5mm angle that then bolts to the same size angle that is welded to a fabricated bracket at the rear and a 50x50 tube at the front.
The seats aren't adjustable fore and aft as I've stopped growing and my wife happens to be the same height.
If you want them adustable yes it will be a mission.
The seat base mounts to 32x32x5mm angle that then bolts to the same size angle that is welded to a fabricated bracket at the rear and a 50x50 tube at the front.
The seats aren't adjustable fore and aft as I've stopped growing and my wife happens to be the same height.
If you want them adustable yes it will be a mission.
Cheers,
Zuffen
There's no such a thing as too much horsepower
Zuffen
There's no such a thing as too much horsepower
I PUT A SET OF IMPORT RACE SEAT IN MY 2 DOOR .
I CUT ABOUT AN INCH OF THE OUTSIDE MOUNTS TO MAKE THEM LEVEL, WELDED A PIECE OF FLAT BAR TO THE TOP ( OF THE SIDE I JUST CUT ).
I USED THE SLIDE MECH FROM AN OLD NISSAN SKYLINE AND PERMANENTLY WELDED THEM TO THE ORIGINAL RANGIE MOUNTS!
THE WHOLE SEAT IS STILL REMOVABLE EITHER BY UNBOLTING THE SEAT FROM THE SLIDE OR BY UNBOLTING EVERYTHING INCLUDING THE RANGIE MOUNT ! THE NEW SEATS ARE ABOUT HALF THE WEIGHT AND THEY SIT ABOUT AN INCH LOWER WHICH IS GOOD BECAUSE I'M A BIG BASTARD ! HOPE THIS HELPS YOU ?
I CUT ABOUT AN INCH OF THE OUTSIDE MOUNTS TO MAKE THEM LEVEL, WELDED A PIECE OF FLAT BAR TO THE TOP ( OF THE SIDE I JUST CUT ).
I USED THE SLIDE MECH FROM AN OLD NISSAN SKYLINE AND PERMANENTLY WELDED THEM TO THE ORIGINAL RANGIE MOUNTS!
THE WHOLE SEAT IS STILL REMOVABLE EITHER BY UNBOLTING THE SEAT FROM THE SLIDE OR BY UNBOLTING EVERYTHING INCLUDING THE RANGIE MOUNT ! THE NEW SEATS ARE ABOUT HALF THE WEIGHT AND THEY SIT ABOUT AN INCH LOWER WHICH IS GOOD BECAUSE I'M A BIG BASTARD ! HOPE THIS HELPS YOU ?
Before you criticize someone, you should walk a mile in their shoes. That way, when you criticize them, you're a mile away and you have their shoes.
i was looking at what i have and i think i will weld a nice bit of thick steel plate over the top of the old seat base and drill my ne holes for the new sliders to bolt onto that. i will also cut the old sliding rails off the old bases. i think that would be a good way to go. hope fully wont be a prob when it goes over the pits.
i was looking at what i have and i think i will weld a nice bit of thick steel plate over the top of the old seat base and drill my ne holes for the new sliders to bolt onto that. i will also cut the old sliding rails off the old bases. i think that would be a good way to go. hope fully wont be a prob when it goes over the pits.
Once you slide the original seats of the bases, these will bolt in on one side, only the tracks prevent them being a straight bolt in. If you grind the tracks off you are left with a flat base with holes along the length and 2 of these line up with the Alfa seat slides.
Saddle up tonto, its the not so loanrangie! . 98 TDI DISCO lightly modded with more to come.
Who is online
Users browsing this forum: No registered users and 3 guests