have read in pommy mags and have a mate that has done it (fabbed up a little plate to block off)...block off the EGR, exhaust gase recycling valve, to promote better performance and economy.
my friend states that he blows less smoke and has made noticable difference in power and economy, as is burning 'cleaner air'?
it was originally done in uk for polution reasons i think?
in mags it states for 'off road use only', is this due to different emission levels?
has anyone done this?
does it have any long term issues? much different power/economy figures?
thinking of doing it to my old mans disco and defender...got make sure its all safe before i do it though....
cheers
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
blocking EGR valve/pipe on TD5's
Moderator: Micka
I always thought EGR was a good thing. But only know about its use on petrol not oil burners. With petrol the exhaust gas contains a certain amount of nitrus oxide which improves the combustion properties and helps retard any pinking.
Ex-Army - SeriesIII -186s - NP435 - Maxi rear - megasquirt coilpack ignition - AM FM radio with 2 X speakers
AFAIK The EGR system on oz Td5's is non operational.
The system is still in place, but when you go in to engine management screens on nearly new vehicles even, the codes for 'EGR valve stuck open' and 'EGR valve solenoid not operational' come up.
The UK, US and other countries have different fuel maps and options etc and some are supported in the ECU's we get and some aren't.
JC
The system is still in place, but when you go in to engine management screens on nearly new vehicles even, the codes for 'EGR valve stuck open' and 'EGR valve solenoid not operational' come up.
The UK, US and other countries have different fuel maps and options etc and some are supported in the ECU's we get and some aren't.
JC
'92 Rangie Sherwood/turbo intercooled isuzu4BD1 /ACE/ full leather/2.5" exh/2.5" body lift/DeCarbon shocks/LR tanks/LT95 back in and OK now, Sals conversion soon...
I wonder if any one in oz has been charged by a dealer for changing a faultly EGR valve ?justinC wrote:AFAIK The EGR system on oz Td5's is non operational.
The system is still in place, but when you go in to engine management screens on nearly new vehicles even, the codes for 'EGR valve stuck open' and 'EGR valve solenoid not operational' come up.
The UK, US and other countries have different fuel maps and options etc and some are supported in the ECU's we get and some aren't.
JC
Good rort. 
A mate of mine got stung $600 to get his replaced on a GQ
Ex-Army - SeriesIII -186s - NP435 - Maxi rear - megasquirt coilpack ignition - AM FM radio with 2 X speakers
Hi There,
as for the EGR valve on the TD5. Here in Europe many people take this valve of there system. I was one of the first ho did this. Why ,my tuner JE engineering said that's one of the first things you wanna take of your car. It recycles the hot air back into the chamber for reburning. It's not a good solution but for the emmisions controls it was placed there.
When my ECU was on there computer i can't remember anything that they had to reset things inside the ECU at al. It a very simple operation. But when i have to go back for MOT then it could be that i have to put it back on. But then i also have to put in another ECU with less horse power and then it wil pas MOT. So you can do that very easy your self. But i can't say that on the standard car it wil bring more horse power. I had it tuned at the same time and that was a big difference. But never have driven a TD5 with a standard tuning and without EGR valve.
Hope this helps you guys,
Regards Rob
as for the EGR valve on the TD5. Here in Europe many people take this valve of there system. I was one of the first ho did this. Why ,my tuner JE engineering said that's one of the first things you wanna take of your car. It recycles the hot air back into the chamber for reburning. It's not a good solution but for the emmisions controls it was placed there.
When my ECU was on there computer i can't remember anything that they had to reset things inside the ECU at al. It a very simple operation. But when i have to go back for MOT then it could be that i have to put it back on. But then i also have to put in another ECU with less horse power and then it wil pas MOT. So you can do that very easy your self. But i can't say that on the standard car it wil bring more horse power. I had it tuned at the same time and that was a big difference. But never have driven a TD5 with a standard tuning and without EGR valve.
Hope this helps you guys,
Regards Rob
Hi,
I can take some photo's but i can explain as wel. You take of the complete EGR valve including the EGR tube what is going arround the cilinderhead to the exhaust manifold. Where the EGR tube was connected to the manifold you using a small plate to block it. Where the complete EGR was fitted you make a small tube what has the same diameter as the rubber hose from the inter cooler. Once that part is made connect it with the spot where the EGR valve was placed,connect the intercooler hose and you are ready. It a very simple operation.
Many 4x4 shops over here selling these parts you are needing. One of them i would say to go for is Devon 4x4 in the UK.
Link to their web site is http://www.devon4x4.com/home
Succes Rob
I can take some photo's but i can explain as wel. You take of the complete EGR valve including the EGR tube what is going arround the cilinderhead to the exhaust manifold. Where the EGR tube was connected to the manifold you using a small plate to block it. Where the complete EGR was fitted you make a small tube what has the same diameter as the rubber hose from the inter cooler. Once that part is made connect it with the spot where the EGR valve was placed,connect the intercooler hose and you are ready. It a very simple operation.
Many 4x4 shops over here selling these parts you are needing. One of them i would say to go for is Devon 4x4 in the UK.
Link to their web site is http://www.devon4x4.com/home
Succes Rob
Can anyone confirm this as I have had issues with my EGR which has been replaced - made a huge difference to the drive and there is no way my mechanic would screw me over like that.justinC wrote:The EGR system on oz Td5's is non operational.
The system is still in place, but when you go in to engine management screens on nearly new vehicles even, the codes for 'EGR valve stuck open' and 'EGR valve solenoid not operational' come up.
Aye, Mick
Hey Mick
Not 100% sure on this, hence the AFAIK preceeding the comment. All I can say is that most of the systems I've seen have had inoperational EGR and/ or fault codes come up on the Rovacom . Even very late models with low K's. Can't comment on your situation though, because if the EGR gets stuck open for real, ( Not just a code in the computer telling you it is...) Then the performance will be no good and there will be LOTS of smoke.
JC
Not 100% sure on this, hence the AFAIK preceeding the comment. All I can say is that most of the systems I've seen have had inoperational EGR and/ or fault codes come up on the Rovacom . Even very late models with low K's. Can't comment on your situation though, because if the EGR gets stuck open for real, ( Not just a code in the computer telling you it is...) Then the performance will be no good and there will be LOTS of smoke.
JC
'92 Rangie Sherwood/turbo intercooled isuzu4BD1 /ACE/ full leather/2.5" exh/2.5" body lift/DeCarbon shocks/LR tanks/LT95 back in and OK now, Sals conversion soon...
The EGR is operation on Aussie TD5's.
Don't bother pulling it all out, its a PITA and makes it difficult if the greenslip man notices. On the EGR block just pull the plug out and that will make it non operational - sometimes this happens when driving down bumpy roads anyway.
I would never admit to doing it as its against the rules, but lets just say I have seen it done in both Discos and Defenders, and it makes an improvement to partial throttle performance and lowish rev performance. The gen1 type TD5's have 1 EGR plug that needs to be pulled, and the gen2 type TD5's have 2 plugs to pull.
Long term issues? You dont get crap in your engine from recirculating exhaust through the inlet so as I understand it any long term differences are beneficial.
Don't bother pulling it all out, its a PITA and makes it difficult if the greenslip man notices. On the EGR block just pull the plug out and that will make it non operational - sometimes this happens when driving down bumpy roads anyway.
I would never admit to doing it as its against the rules, but lets just say I have seen it done in both Discos and Defenders, and it makes an improvement to partial throttle performance and lowish rev performance. The gen1 type TD5's have 1 EGR plug that needs to be pulled, and the gen2 type TD5's have 2 plugs to pull.
Long term issues? You dont get crap in your engine from recirculating exhaust through the inlet so as I understand it any long term differences are beneficial.
Cheers
Slunnie
Discovery TD5, Landy IIa V8 ute.
Slunnie
Discovery TD5, Landy IIa V8 ute.
Interseting....what am I looking for then under my bonnet....any chance of a pic, might give it a try now and see what happens - mine is a '99 TD5.Slunnie wrote:The EGR is operation on Aussie TD5's.
Don't bother pulling it all out, its a PITA and makes it difficult if the greenslip man notices. On the EGR block just pull the plug out and that will make it non operational - sometimes this happens when driving down bumpy roads anyway. ;)
I would never admit to doing it as its against the rules, but lets just say I have seen it done in both Discos and Defenders, and it makes an improvement to partial throttle performance and lowish rev performance. The gen1 type TD5's have 1 EGR plug that needs to be pulled, and the gen2 type TD5's have 2 plugs to pull.
Long term issues? You dont get crap in your engine from recirculating exhaust through the inlet so as I understand it any long term differences are beneficial.
Cheers, Mick
That looks like the plug I was thinking about but until someone can confirm that's the plug, i'm leaving it in........tried to take it out anyway and it's pretty tight, is there a trick to getting it out?
Last edited by Mick G on Thu Mar 30, 2006 3:55 pm, edited 1 time in total.
The plug is black and it has a blue and a brown wire that leads to it.
On both the Disco and Defender it is on the Drivers side. The Disco has the module under the brake booster area, and the Defender inide the wing about 1/2 way forward and at the top. The Defenders that I "looked" at had 2 plugs on each and they both had fallen off. The 2000 Disco had one that had also fallen off.
On both the Disco and Defender it is on the Drivers side. The Disco has the module under the brake booster area, and the Defender inide the wing about 1/2 way forward and at the top. The Defenders that I "looked" at had 2 plugs on each and they both had fallen off. The 2000 Disco had one that had also fallen off.
Cheers
Slunnie
Discovery TD5, Landy IIa V8 ute.
Slunnie
Discovery TD5, Landy IIa V8 ute.
EGR plate
Go to www.scorpionracing.co.uk (if you want to spend the money) and they sell and EGR removal kit. Click on products, then performance, and then general. Theres a picture of the kit. Rovacraft pty ltd (08) 9377 0080 in W.A. is their Australian dealer.........
Hope this is of help
Hope this is of help
Now a 2005 Td5 defender wagon..
nah i boxed in at work now so wont get a chance till the end of the day :(
i used a screw driver to press the metal clip in as far as i could (come in from the bottom) and with my left hand wiggle the plug off. wasnt easy but it came loose.... let me know if you have oil in yr plug too pls
Mick
i used a screw driver to press the metal clip in as far as i could (come in from the bottom) and with my left hand wiggle the plug off. wasnt easy but it came loose.... let me know if you have oil in yr plug too pls
Mick
TD5 96 Discovery UTE.
Cheers Mick, will give it a shot now and see if I can get it off....will keep you posted.mickrangie wrote:nah i boxed in at work now so wont get a chance till the end of the day :(
i used a screw driver to press the metal clip in as far as i could (come in from the bottom) and with my left hand wiggle the plug off. wasnt easy but it came loose.... let me know if you have oil in yr plug too pls
Mick
Aye, Mick
Who is online
Users browsing this forum: No registered users and 11 guests