Hi guys,
i am having an issue with the consumption of my Feroza 1,6i of the 1990.
I am currently at 7 Km/liter, but , from the last time i checked (about 5 weeks ago) was 10-11 Km /liter !!!
I have not changed anything from that time and the car is , or at least seem to be OK. (No power loss, minimum regular, no different way how i drive...
My car has 225/70/15 tyre, K&N airfilter, 4in1 Genie extractor on.
Any suggestion will be areally ppreciated.
Ciao from Italy
Achille
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Increased consumption !!!
Moderator: Tiny
hi, Check your coolant temp. sensor. because if it is faulty it will give the computer a faulse reading (that is that the engine is cold) and it will keep pumping petrol in all the time (more than usual). Feroza's run rich when they are cold and then when the coolant temp sensor sends a signal to the ECU that the car is warmed up it changes the fuel delivery. The coolant temp sensor is located under the dizzy, the one that has two wires on it. not the one with 1 wire on it, that controls the temp gauge. See how you go with that.
Alandra, is the sensor screwed directly into the block, or is it screwed into one of the coolant outlets? I've looked for mine a couple of times with little success.
I know the most visible coolant "sensor" in that area is actually a thermo switch to cut the aircon out if the coolant temp gets too high.
I know the most visible coolant "sensor" in that area is actually a thermo switch to cut the aircon out if the coolant temp gets too high.
David
Hallo and thanks for the suggestions:
i checked the O2 using all Murcod suggetions: the O2 sensor is OK
I was looking for the Temp. sensor (below the distributor) w/o success.
I was completely layed down ON the engine , but was not able to reach it.
Do you have a picture how is made ?
How do you reach it ? Did you have removed the distributor ?
Do you have the code for this sensor (my car engine is injection type of early 1990).
Sorry for the lot of question
Thanks
Ciao
Achille
i checked the O2 using all Murcod suggetions: the O2 sensor is OK
I was looking for the Temp. sensor (below the distributor) w/o success.
I was completely layed down ON the engine , but was not able to reach it.
Do you have a picture how is made ?
How do you reach it ? Did you have removed the distributor ?
Do you have the code for this sensor (my car engine is injection type of early 1990).
Sorry for the lot of question
Thanks
Ciao
Achille
how exactly do you check the temp sensor to see if it is working correctly? Have same problem with mine, just replaced O2 and it helped a little but it gas mileage is crap (around 18 miles per gallon.) Should n't it get around 30 mpg? Would a missing catalytic converter cause any part of this? Cause my friend is missing his.
to check the coolant temp sensor you can do it 2 ways, the hard way and the harder way. 1. locate temp sensor under dizzy, easiest way from under the car. unplug the sensor and check its continuity. i'm not too sure what that resistance reading should read i cant remember. 2. Locate ECU, passanger side kick panel. obtain wiring diagram, check colour of wires on coolant temp sensor, find these wires at the ecu, check the resistance reading that way. (when doing this way make sure the coolant temp sensor is pluged in). there should be 2 resistance readings, one for engine cold conditions, and the other for engine hot conditions. hope this helps. If still having dramas and you live in sydney come by my workshop. the address is
4/203 cnr Fairfield Rd & Foray st Guildford West 2161
Alandra Auto Electrics.
Ask For Jason.
4/203 cnr Fairfield Rd & Foray st Guildford West 2161
Alandra Auto Electrics.
Ask For Jason.
A shameless advert! Seriously thanks for your input Jason. 
The Service Manual and HD-E Engine Manual have all the good stuff on what wires at the ECU end you'll need to check (and it's not that hard to access -> front passenger side kick panel just under the glovebox.) The manuals also give all the resistance / voltage specs.
The water proof EFI connectors in the engine bay can be a right PITA to remove on the Feroza engines, so the ECU could be a good option.
The Service Manual and HD-E Engine Manual have all the good stuff on what wires at the ECU end you'll need to check (and it's not that hard to access -> front passenger side kick panel just under the glovebox.) The manuals also give all the resistance / voltage specs.
The water proof EFI connectors in the engine bay can be a right PITA to remove on the Feroza engines, so the ECU could be a good option.
David
Who is online
Users browsing this forum: No registered users and 35 guests