Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

fuse hot to touch

For all things Electrical.

Moderator: -Scott-

Forum rules
Post Reply
Posts: 644
Joined: Wed Sep 01, 2004 3:11 pm
Location: N.S.W

fuse hot to touch

Post by tuf045 »

I have a hj47 land cruiser and the head light fuse is hot to touch after driving five minutes with the headlights on, any ideas?
Reptile fabrication.
www.agroautomotive.net
Top
Posts: 3722
Joined: Sat Jan 18, 2003 7:32 pm
Location: perth wa

Post by bazooked »

dont touch it :D
buggy time............
Top
Posts: 14209
Joined: Sun Jan 11, 2004 11:36 am
Location: Adelaide

Post by -Scott- »

"Hot to touch" could be 50 degrees. Few aluminium alloys will soften below 450 degrees, so I wouldn't be too concerned.

If you're really worried, pull out the fuse and clean all the contacts.

Scott
Top
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Post by toughnut »

Have you changed your bulbs from standard? My fuse for my thermos was doing the same because they were drawing just a bit too much current and melting fuses but not enough to amps to blow the fuse. solution for me was to split the thermo's into two fuses. ;)
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Top
Posts: 2384
Joined: Mon Mar 31, 2003 10:05 am
Location: Brisbane or 169.254.243.241

Post by RaginRover »

How big is the fuse and how many headlights and what size are the bulbs ?

Tom
Top
Posts: 558
Joined: Sat Dec 11, 2004 4:38 pm
Location: Gold Coast

Contact:
Contact drivesafe

Post by drivesafe »

Hi tuf045, fuses getting warm is common but make sure the wire running to you lights is not getting the slightest bit warm or you will have problems.

Even just the fuse getting hot will cause a slight voltage drop and as such, a light voltage drop will cause your lights to dull ever so slightly.

Cheers.
2007 TDV8 Range Rover Lux
2009 2.7 Discovery 4
Top
Posts: 644
Joined: Wed Sep 01, 2004 3:11 pm
Location: N.S.W

hot

Post by tuf045 »

toughnut wrote:Have you changed your bulbs from standard? My fuse for my thermos was doing the same because they were drawing just a bit too much current and melting fuses but not enough to amps to blow the fuse. solution for me was to split the thermo's into two fuses. ;)
yes the i have 90/110s in the semi sealed beams and have been told to add a relay to the headlights as on this model the headlights only have a fuse and no relay, So will try that and see what happens.

thanks for the replies all.
Reptile fabrication.
www.agroautomotive.net
Top
Posts: 192
Joined: Tue Dec 20, 2005 1:37 pm
Location: Brisbane

Post by spannercrab »

Had a HJ45 (close enough :) - fuse would get hot then lights would cut out ... running 90/110's ... problem was / is corrosion on the terminals / fuse itself - causes high resistance connection - which causes heat.

Upgrading to new loom (can get kits for cheap on eBay) is definately a wise choice - as the light switch on these things IS the switch which carries all the current to the lights ... after 30 years of use, the contacts tend to get a bit dirty / warm - also the wiring isn't exactly high capacity.

Fuse fix was just to clean the fuse & holder etc with emery paper / files ... whatever was available.

Upgraded the wiring loom also to 6mm running a pair of relays with external fuses straight to the battery. Fixed up them lighting problems good.
If it's worth doing - it's worth doing to excess ...
Top
Post Reply

Return to “Auto Electrical”

Who is online

Users browsing this forum: No registered users and 1 guest