Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Front Diff

Tech Talk for Jeep owners.

Moderator: GUtripper

Post Reply
Posts: 26
Joined: Wed Feb 01, 2006 7:18 pm
Location: taree

Front Diff

Post by riley »

Looking to go a bit harder. Have been told the Dana 30 will not stand up to comps.Asking advice on up grades for the front diff.
NISSAN gu 4.2 turbo 2'' ome,33'' coopers
Posts: 322
Joined: Fri May 21, 2004 12:10 am

Post by Steve F »

XJ high pinion D30 is supposed to be a bit stronger, then there's the Super 30 which I think is comparable with a Dana 44 up front (30 housing with stronger internals). You could then look at a real Dana 44 and beef that up, or maybe a Dana 60. Quite a lot of options depending on cash.

In saying that Wooders has done two tuff trucks with a low pinion Dana 30 in the front of his TJ and it still lives. He was running 36" tyres I think. Most of the daily driver/comp TJs still run a D30 housing at least, not many have swapped in anything else.

Cheers
Steve
Posts: 1544
Joined: Tue Oct 22, 2002 8:37 am
Location: Performing booty fab in my Garage

Post by Wooders »

Riley,

Speifically what sort of comps are you looking to enter and what's the maximum tyre size you plan to run?
The dana30 is a bit ouny - but it's not really as weak as some make out - so if you can enlighten us to your plans we might be able to add some more value to our input ;)
Cheers [url=http://www.wooders.com.au]Wooders[/url]
User avatar
stu
Posts: 913
Joined: Wed Jan 22, 2003 8:08 am
Location: brisbane

Post by stu »

your best bet is to do as the woods man says......but.....theres aftermarket axels out there, whole axel upgrades from 28 to 31 spline ( i think) and the thing can be braced for strength...that should be plenty strong enough for most.
i don't need no stinking quote for my sig. line!
Posts: 26
Joined: Wed Feb 01, 2006 7:18 pm
Location: taree

Post by riley »

I am planning on winch challange events.So my tyre size would be 35s to 36 max.Thanks for the help.
NISSAN gu 4.2 turbo 2'' ome,33'' coopers
User avatar
stu
Posts: 913
Joined: Wed Jan 22, 2003 8:08 am
Location: brisbane

Post by stu »

wooders ran 36 simex ( i think ) at tuff truck for th elast two years.

since its a winch event ( hi-speed running and slowly getting dragged over stuff ) id brace the axle tube, upgrade the tie rod to Skyjacker HD unit, install a diff guard, and get some chromo. axles to replace the factoy units.
i don't need no stinking quote for my sig. line!
User avatar
stu
Posts: 913
Joined: Wed Jan 22, 2003 8:08 am
Location: brisbane

Post by stu »

theres a scouts dana 44 with air locker and 4.1 ratios for $1800 in the for sale section if ya really concermed.
i don't need no stinking quote for my sig. line!
Posts: 1128
Joined: Sat Jul 26, 2003 4:29 pm
Location: Brisney Land

Post by Thor »

stu wrote:wooders ran 36 simex ( i think ) at tuff truck for th elast two years.

since its a winch event ( hi-speed running and slowly getting dragged over stuff ) id brace the axle tube, upgrade the tie rod to Skyjacker HD unit, install a diff guard, and get some chromo. axles to replace the factoy units.
swampers i believe.

IMHO i would build the 30 and unless you're going every weekend and giving it a real hard time and breaking it.. then consider it as a future mod down the track.
[img]http://www.users.bigpond.com/krome1/sailor.gif[/img] (O]]]]]]O)
Posts: 26
Joined: Wed Feb 01, 2006 7:18 pm
Location: taree

Post by riley »

Thanks guys for the info i might build up the 30 it sounds like the way to go.
NISSAN gu 4.2 turbo 2'' ome,33'' coopers
Posts: 1544
Joined: Tue Oct 22, 2002 8:37 am
Location: Performing booty fab in my Garage

Post by Wooders »

Yeah I was n 36" TSL's.
Anyhow one good thing about the dand30 is it's small. and that means good axle clearance when competing in a class of limited tyre size - ie hopefully a bit more clearance than your fellow competitor on similar sized meats.
The other thing is most winch challenges are about power & weight - and the dana 30 IS nice & light.

IMHO if I was building (& pepared to spend some coin) for winch challenge I'd go:
XJ high pinion D30. Truss the bejessus out of it (benting the tubes is one of the more likely senarios otherwise).
Then go fo a Super 30 upgrade which gives you thicker shaft with more splines.
I'd also go for WJ knuckles with the dual piston brakes - all the more important is you have speed sections.
I'd probably stay wth a 4.56 ratio to keep a bit more meat on the teeth than you get with the 4.88 ratio.
Many get a hub convesion from Warn - but after you've blown the 3rd hub give us a yell & we'll supply one of our fixed hubs ;)

Only problem is I;ve just blown a heap of coin on the above setup....
Another option would be to build a 9" diff to suit. Jp did an article about 18months ago where they build one and made it extremely light by:
Using a spool not a locker (much lighter),
They used gun barrellel drilled shafts,
They CNC'ed long sections of metal from the tubes to shave weight off. they also drilled the knuckles out,
rom memory the used an alloy 3rd member too......
But at the end of it they had a string but light axle....just what you really need - just expect to spend big for that sort of setup.

Anyhow my 2 main suggestion are focus on 1. Clearance & 2. Weight.
Strength is 3rd.....
Cheers [url=http://www.wooders.com.au]Wooders[/url]
Posts: 4882
Joined: Fri Nov 08, 2002 8:36 pm
Location: Medowie, NSW

Post by redzook »

Wooders wrote:
Anyhow my 2 main suggestion are focus on 1. Clearance & 2. Weight.
Strength is 3rd.....
clearance and weight are no good if you cant finish the track cos your broken

strength and reliability should be the number one priorty

followed by clearance

then weight ( diffs are the lowest things to the ground a good place for weight)
Team UNDERDOG #233
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
Posts: 7954
Joined: Fri Sep 05, 2003 5:43 pm
Location: Tasmania

Post by DeWsE »

One of the guys over here has been wheeling rocks with a D30 on 37's for quite some time now without a problem. The axles are chromo with warn hubs... But in saying that there are also guys over here breaking stuff in the ruts with 35's. Get someone to watch your driving style and I think they will be able to give you important information about your driving. EG. You would get caught one rock if it was the only rock over one hundred square meters.
[quote="STD CONSUMER"]haha, i'm tellin you, my camp was hard to find on Saturday night!
then i shared my bed with 2 second tom... [/quote]
Posts: 26
Joined: Wed Feb 01, 2006 7:18 pm
Location: taree

Post by riley »

Guys
Is it worth putting Warn free wheeling hubs in .
NISSAN gu 4.2 turbo 2'' ome,33'' coopers
User avatar
stu
Posts: 913
Joined: Wed Jan 22, 2003 8:08 am
Location: brisbane

Post by stu »

No.....from what i hear they grenade quite often.
i don't need no stinking quote for my sig. line!
Posts: 1544
Joined: Tue Oct 22, 2002 8:37 am
Location: Performing booty fab in my Garage

Post by Wooders »

stu wrote:No.....from what i hear they grenade quite often.
Unless you fit upgraded Hubs ;)
Cheers [url=http://www.wooders.com.au]Wooders[/url]
Posts: 399
Joined: Mon Nov 25, 2002 5:29 pm
Location: Sydney

Post by AussieCJ7 »

Wooders wrote:
stu wrote:No.....from what i hear they grenade quite often.
Unless you fit upgraded Hubs ;)
or 5 on 5.5 full floater upgrade :) :finger:
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest