Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
rangie ute engineering help
Moderator: Micka
rangie ute engineering help
just wondering if any of you who have gone through the engineering process with your utes could tell me what the engineers look at just so i have a heads up as im am still doing my conversion. anything i can do to make it easier will help. cuirrently i have used box section to build a cage and 2.5 mm steel plating to build my rear cab wall. i intend to add an inside roll bar of about 3inch diameter with cross bracing. is this over kill or will it make it easier for me?
pics of my yella machine at
http:\\community.webshots.com/user/tcpr_024
http:\\community.webshots.com/user/tcpr_024
where are you exactly? in melb I'm going through "torque talk" and the only 2 things he picked on me (we'd already chopped...) were how i attached the alloy roof to the steel frame, for corrosion and longevity issues.
and 2 extra gussets on the support frame of the back panel
gusset 1
Gusset 2
ignore the welds, we were using the wrong sorta welder in a rush
Simon
and 2 extra gussets on the support frame of the back panel
gusset 1
Gusset 2
ignore the welds, we were using the wrong sorta welder in a rush Simon
I done mine exactly the same.loanrangie wrote:I just have mine self tappered as per original and the roof has been cut down and i used one of the steel ribs and a piece of offcut roof and rivetted it together.
i asked the same thing, this is almost exactly how my engineer explained it...mickrangie wrote:shakes wrote:
how i attached the alloy roof to the steel frame, for corrosion and longevity issues
dose that really matter for engineering?..... i am going to do ute conversion but i am using fibreglass roof.....
how much has it cost use
uncoated alloy+steel = rust
rust + engineered ute chop in rollover with fatalitys/injurys can be shown as me not doing my job properly, and then he went on to complain about having to think like a lawyer.
the chop itself cost one of my mates alot of his time (was his car before mine) and realistically it cost him 2x slabs for the steel he used, and 2k for a good mig which he's since sold for $1800
stick some pics of your utes up!!!
Simon
shakes wrote:I done mine exactly the same.loanrangie wrote:I just have mine self tappered as per original and the roof has been cut down and i used one of the steel ribs and a piece of offcut roof and rivetted it together.
mickrangie wrote:shakes wrote:
how i attached the alloy roof to the steel frame, for corrosion and longevity issues
dose that really matter for engineering?..... i am going to do ute conversion but i am using fibreglass roof.....
how much has it cost use
i asked the same thing, this is almost exactly how my engineer explained it...
uncoated alloy+steel = rust
rust + engineered ute chop in rollover with fatalitys/injurys can be shown as me not doing my job properly, and then he went on to complain about having to think like a lawyer.
the chop itself cost one of my mates alot of his time (was his car before mine) and realistically it cost him 2x slabs for the steel he used, and 2k for a good mig which he's since sold for $1800
stick some pics of your utes up!!!
Simon
Simon, when Mick asked how much it cost, I think he meant the engineering.
Thanks,
Adam
Adam
uted rangie
I used a alloy rear panel which is welded to the roof the pannel is held onto the steel frame with a urethane used by pannel beaters as a body adheasive and pop rievetts so far no signs of rust . will be engineered very sone so will see .
Fanks that what the info i was after... I am going to use LRA ute kit and i have all the lra body lift and sus kit installed so i dont think i should have any problems.... + i am going to have to get it engineered with 33" road tyres unless i find som 35"shakes wrote:$132ph off the top of my head.
took 1½hrs for initial inspection.
being that I'm using LRA's body lift (among other things) all the rest of the stuff (brake testing etc) is essentially pre-approved so alot of time and money is saved there!
Simon
TD5 96 Discovery UTE.
The body lift kit that Andrew now sells and has got engineering approval for is a fair bit different to the old kit that you and I have on ours. May not be so easy to get engineered.mickrangie wrote:[I am going to use LRA ute kit and i have all the lra body lift and sus kit installed so i dont think i should have any problems....
Range Rover - 4.4 V8, MD Crawler Box, F&R Lockers, 35" Centipedes, 4" lift. Overqualified WebWheeler!!!
Discovery - Bling touring stuff!
Discovery - Bling touring stuff!
heres where im up to. got heaps to go. got a new sill to put in on the drivers side....also my idea for attaching the roof is by using a piece of steel cut/bent/welded to match the shape of the roof and then riveting it in place inside the cab and using fibre glass to fill the join on the rear outside .....if you know what i mean...
pics of my yella machine at
http:\\community.webshots.com/user/tcpr_024
http:\\community.webshots.com/user/tcpr_024
gee looks like that might rust out before it done...yella_rangie wrote:heres where im up to. got heaps to go. got a new sill to put in on the drivers side....also my idea for attaching the roof is by using a piece of steel cut/bent/welded to match the shape of the roof and then riveting it in place inside the cab and using fibre glass to fill the join on the rear outside .....if you know what i mean...
TD5 96 Discovery UTE.
Who is online
Users browsing this forum: No registered users and 0 guests