Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

after a stainless steel snorkel.....MELB

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 118
Joined: Tue Aug 22, 2006 9:23 am
Location: Melbourne

after a stainless steel snorkel.....MELB

Post by Charged_ZooK »

i need say 3" pipe no bends.. i need say 2 meters......

if anyone nows a plane in melbourne.....

thanks

peter
Top
Posts: 771
Joined: Wed Jun 23, 2004 9:34 pm
Location: greensborough, vic

Post by big bundy »

got mine from tubesales in tomastown.

sorry can't rember the price tho.
bundy's suck ass
LWB patrol's are where its at!
Top
Posts: 156
Joined: Fri Aug 25, 2006 6:33 pm
Location: MELBOURNE

Post by TURBO GQ »

x2 ;)
Top
Posts: 118
Joined: Tue Aug 22, 2006 9:23 am
Location: Melbourne

Post by Charged_ZooK »

thanks buddy...... ill give them a try tomorrow....

cheerz

peter
Top
Posts: 48
Joined: Wed Jan 14, 2004 11:00 pm
Location: Thomastown, Vic

Re: after a stainless steel snorkel.....MELB

Post by GQPatrol V8 »

Charged_ZooK wrote:i need say 3" pipe no bends.. i need say 2 meters......

if anyone nows a plane in melbourne.....

thanks

peter

Tube sales in Temple drive Thomastown, They should have stainless mandel bends as well.

Very freindly service. Mate deals with them a lot.

Shane
Top
Posts: 118
Joined: Tue Aug 22, 2006 9:23 am
Location: Melbourne

Post by Charged_ZooK »

cheap as...... for 3" tube no bends at $22 a meter.!!!

my concern is one of my mate on his patrol has this set up but he has joint the stainless steel with 90 degree and 45 degree black rubber bends.... i dont no were to get these.. i have tried reece plumbing altho they dont no what i talk about...... :? i dont want manderal bends due to i dont partuicually like seeing the welds!!!!!

HELP ME :roll: :roll:
Top
Posts: 13555
Joined: Fri Nov 15, 2002 1:28 pm
Location: Melbourne

Post by grimbo »

Charged_ZooK wrote:cheap as...... for 3" tube no bends at $22 a meter.!!!

my concern is one of my mate on his patrol has this set up but he has joint the stainless steel with 90 degree and 45 degree black rubber bends.... i dont no were to get these.. i have tried reece plumbing altho they dont no what i talk about...... :? i dont want manderal bends due to i dont partuicually like seeing the welds!!!!!

HELP ME :roll: :roll:
why would you see the welds if you manderal bend something?
Ransom note = demand + collage
Top
Posts: 19062
Joined: Sat Oct 25, 2003 11:39 pm
Location: In a horse near you

Post by chimpboy »

grimbo wrote:
Charged_ZooK wrote:cheap as...... for 3" tube no bends at $22 a meter.!!!

my concern is one of my mate on his patrol has this set up but he has joint the stainless steel with 90 degree and 45 degree black rubber bends.... i dont no were to get these.. i have tried reece plumbing altho they dont no what i talk about...... :? i dont want manderal bends due to i dont partuicually like seeing the welds!!!!!

HELP ME :roll: :roll:
why would you see the welds if you manderal bend something?
I think he's referring to the bends that you buy and then weld in between sections of straight pipe.

Anyway I reckon the black rubber bends look better than steel bends, just personally, as well as being more DIY-friendly.
This is not legal advice.
Top
Posts: 1443
Joined: Tue Apr 12, 2005 3:57 pm
Location: Brisbane

rubebr bends.

Post by vanbox »

the black rubber bends should be able to be located at any truck spares place. im from sunny qld and the pipe is the same price up here, thats good to know...

Image

cheers
PAUL
MUD BEERS and MAYHEM

DURAMAX POWERED GU
Top
Posts: 118
Joined: Tue Aug 22, 2006 9:23 am
Location: Melbourne

Post by Charged_ZooK »

yeah i want the bends.... does anyone no where to get them from.....?????
Top
Posts: 118
Joined: Tue Aug 22, 2006 9:23 am
Location: Melbourne

Post by Charged_ZooK »

what do i ask for aswell....?? wat they called????

i am a little simple... only as student......... :? :? :?
Top
Posts: 2775
Joined: Thu Apr 13, 2006 8:59 pm
Location: Melbourne

Post by GQ Bear »

There's a massive truck spares joint on sth gippy hwy dandenong. I might drop in and check it out. As for what they're called or used for i don't know...yet.

they may even have 'em in 4" :armsup:
[color=violet]G[/color][color=white]O[/color][color=yellow] S[/color][color=blue]T[/color][color=yellow]O[/color][color=white]R[/color][color=violet]M[/color]
Premiers 1999, 2007, 2009
Spoon 2010
Top
Posts: 156
Joined: Fri Aug 25, 2006 6:33 pm
Location: MELBOURNE

Post by TURBO GQ »

GQ Bear wrote:There's a massive truck spares joint on sth gippy hwy dandenong. I might drop in and check it out. As for what they're called or used for i don't know...yet.

they may even have 'em in 4" :armsup:
thanks for that GQ Bear ;)
Top
Posts: 771
Joined: Wed Jun 23, 2004 9:34 pm
Location: greensborough, vic

Post by big bundy »

yurp, called truck spares i think, just premoulded rubber bends for intakes. cost me around 90 bucks i think for two 45's and a 90. when u cut the hole in the guard, go to clark rubber and get a rubber strip with a groove cut down it, cut it so it covers up the cut, i can get a pic if need be???
bundy's suck ass
LWB patrol's are where its at!
Top
Posts: 281
Joined: Sat Dec 20, 2003 5:45 pm
Location: Gold Coast - Pac Pines

Contact:
Contact Bowhunter

Re: rubebr bends.

Post by Bowhunter »

vanbox wrote:the black rubber bends should be able to be located at any truck spares place. im from sunny qld and the pipe is the same price up here, thats good to know...

Image

cheers
PAUL
Hey mate, where bouts did you get your quote from?

cheers,

Luke :P
[url=http://www.aussiebowhunter.com][b]Founder TBGA - September 29, 2001 - Australia's Premier Bowhunting Site[/b][/url]
Top
Posts: 95
Joined: Mon Oct 10, 2005 11:38 am
Location: Brisbane, Sumner Park

Post by fnukle »

^ Same question here Paul
thanks :)
Top
Posts: 118
Joined: Tue Aug 22, 2006 9:23 am
Location: Melbourne

Post by Charged_ZooK »

thanks for that fellaz..... i will be sure to give that truck place a bell.....


they look way better than say a safari snorkal.... and besides the fact you can replace insted of buying a new one if gets tiped on.... :D :D :D

can you post up that pic big bundy......????.

thanks
Top
Posts: 2186
Joined: Wed Oct 01, 2003 9:11 pm
Location: Melbourne, now with 1HDFTi power!

Contact:
Contact +dj_hansen+

Post by +dj_hansen+ »

Truck bits in dandenong/bayswater

90^ bend 3" - $19.80
45^ bend 3" - $26.50
Donaldson Ram head (safari style) 3" inlet - $36

those prices were as of bout 6 weeks ago when i was pricing :)

you also have to buy the pipe clamps for the rubber bends which were about $4 each...
Cheers,
Dan.

[i]1996 HDJ80R[/i]
Top
Posts: 1254
Joined: Mon May 16, 2005 8:21 pm
Location: Sth Brissy

Contact:
Contact LuxyBoy

pipe

Post by LuxyBoy »

fnukle wrote:^ Same question here Paul
thanks :)

X3 :D
and what did you use to stick yours to the vehicle with :?:
Kind Regards,
Brad
Top
Posts: 791
Joined: Fri Mar 17, 2006 7:45 pm
Location: Gold Coast QLD

Post by NCpaj »

Truck bits in dandenong/bayswater

90^ bend 3" - $19.80
45^ bend 3" - $26.50
Donaldson Ram head (safari style) 3" inlet - $36

those prices were as of bout 6 weeks ago when i was pricing

you also have to buy the pipe clamps for the rubber bends which were about $4 each...
yeah its not that expensive
http://www.4wdmonthly.com.au/forum/inde ... adid=16416

i made mine the same way but used some black plastic tube from bunnings :D
Real men smoke clutches
86' Pajero
2" OME, steel bar goodness, MTZ's, Exxon Valdez-esk fuel consumption
Top
Posts: 3132
Joined: Wed Sep 28, 2005 3:22 pm
Location: Newy

Post by HotFourOk »

I did the same with mine
Image

Got them from Robertson Brothers Truck Spares here in Newy... They are the local Donaldson dealer.

The 45 deg was $28 and the 90deg was $19... go figure.. lol
[quote="RockyF70 - Coming out of the closet"]i'd be rushing out and buying an IFS rocky[/quote]
Top
Posts: 118
Joined: Tue Aug 22, 2006 9:23 am
Location: Melbourne

Post by Charged_ZooK »

yea thats the shit dude :D :D thats look great.... where is this place in melb for the truck spairs.....????
Top
Posts: 117
Joined: Thu Jun 22, 2006 8:03 am
Location: MELBOURNE

Post by rochrd »

There's a massive truck spares joint on sth gippy hwy dandenong
round here somewhere!!!! ;)
Top
Posts: 118
Joined: Tue Aug 22, 2006 9:23 am
Location: Melbourne

Post by Charged_ZooK »

yea i have found it on whereis.com.au and i found it... its only around 30 mins from mine......... i might give them a call....

hey turbo GQ are you wanting some bends........????

i will be getting 2.. 45s and 1.. 90 degrees.... in 3"
Top
Posts: 117
Joined: Thu Jun 22, 2006 8:03 am
Location: MELBOURNE

Post by rochrd »

make it thursday ill come with ya. ;)
Top
Posts: 156
Joined: Fri Aug 25, 2006 6:33 pm
Location: MELBOURNE

Post by TURBO GQ »

:armsup: :D :lol: HEHEHE
YEAH HEHEHE
IM FUNNY ANT I
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 1 guest