Rod Holders

Post by **bruiser** » Mon Sep 11, 2006 5:16 pm

Where is a good place to buy rod holders from in Brisbane. And I'm talking steel or stainless not aluminum. Everywhere I've looked seems to only stock aluminum ones.

Have an aluminum set. Absoulte waist of time.

Website · Post by **LuxyBoy** » Mon Sep 11, 2006 6:13 pm

Why

What is your problem with the ali ones

I have ali and they do the job fine

Post by **chimpboy** » Mon Sep 11, 2006 6:17 pm

I would have though aluminium would be okay... but anyway, they look very basic to make so why not make your own from steel? Then you could design some that won't stick (illegally) forward of the bullbar like they all seem to do.

Post by **rojak** » Mon Sep 11, 2006 6:55 pm

TJM make decent ones for about $50 with good mounting clamps, fairly solid in either silver or black.

Post by **chimpboy** » Mon Sep 11, 2006 7:00 pm

rojak wrote:TJM make decent ones for about $50 with good mounting clamps, fairly solid in either silver or black.

Aren't the TJM ones aluminium though?

Post by **rojak** » Mon Sep 11, 2006 7:12 pm

May be alloy but they are solid unlike some of the beer can ones that the tackle shops sell.

Post by **bruiser** » Mon Sep 11, 2006 7:16 pm

My aluminum ones are crap. Crap I tell you. I have to tighten them so tight that they are bending around the bar before they stop moving on the bar. Even then the rods twist them when i go over bumps.
Will never buy aluminum again. Don't care how ell made they are. It just aint strong enough when you have 4 x 13 foot rods in them.

Post by **rojak** » Mon Sep 11, 2006 7:23 pm

bruiser wrote:My aluminum ones are crap. Crap I tell you. I

Will never buy aluminum again. Don't care how ell made they are. It just aint strong enough when you have 4 x 13 foot rods in them.

Bit of a contradition there, never buy alloy irrelevant of how well made they are.

There are some great alloy products, unfair to bag all the products because your example may be a POS.

Post by **PJ.zook** » Mon Sep 11, 2006 7:27 pm

The man wants steel dammit!

Post by **bruiser** » Mon Sep 11, 2006 7:37 pm

I meant ally rod holders.

PJ.zook wrote:The man wants steel dammit!

Thankyou.

Website · Post by **LuxyBoy** » Mon Sep 11, 2006 8:49 pm

Yeah mine bend round to i know what you mean

Do the job for now until my tube bar comes

don't know what i am going to do then

Post by **GoTheLux** » Mon Sep 11, 2006 9:23 pm

try putting a piece of thin rubber like an old inner tube around the bullbar then clamp up tight on that might stop the slipping.

Post by **Rb25sil80** » Thu Sep 14, 2006 2:16 pm

Hmm I just use the $25 wilson model from the tackle shop, fairly sure its alloy. Has 2 13 footers and 2 15s and I havnt tightened it since I bought it. Nothing wrong with alloy rod holders, you must have just bought shit ones.

Post by **bogged** » Thu Sep 14, 2006 2:53 pm

I thought they were illegal now - no forward protrusions from the bar....

I remember a thread from some dude ages ago gettin nailed for em was very pricey fine too...

Post by **bruiser** » Thu Sep 14, 2006 3:02 pm

Thanks for answering the question guys.

Post by **of4x4** » Thu Sep 14, 2006 4:05 pm

chimpboy wrote:
rojak wrote:TJM make decent ones for about $50 with good mounting clamps, fairly solid in either silver or black.
Aren't the TJM ones aluminium though?

Yes, they are alluminim (but look solid).

http://www.tjm.com.au/Default.aspx?tabid=64

Sorry Bruiser, can't help you with steel ones I'm afraid. Good Luck!

Post by **rojak** » Thu Sep 14, 2006 5:58 pm

The tjm bar comes with muffler clamps ( or mine did anyway)

The rod base plate sits flat on the clamp, when tight it doesn't spin.[/img]

Post by **Spud76** » Fri Sep 15, 2006 8:49 am

Rb25sil80 wrote:Hmm I just use the $25 wilson model from the tackle shop, fairly sure its alloy. Has 2 13 footers and 2 15s and I havnt tightened it since I bought it. Nothing wrong with alloy rod holders, you must have just bought shit ones.

x2 I use the same never had a problem with them

I have never seen Stainless ones before if anyone does make them I think they would be pretty expensive.

If the ally ones are spining on your bar what makes you think steel won't??

Post by **Shadow** » Fri Sep 15, 2006 9:14 am

bogged wrote:I thought they were illegal now - no forward protrusions from the bar....

I remember a thread from some dude ages ago gettin nailed for em was very pricey fine too...

They are illegal to have fitted when not in use.

As many people do leave the fitted when not in use (see them every day) they will eventually be banned outright.

You can be fined $125 in QLD for having it fitted without a rod in it. Even if you say "im going to the tackle shop to pick up my rod"

No doubt there are several people posting in this thread that have them fitted when not in use. To those people i say why? lazy? dumb? didnt know it was illegal? trying to get them banned? retarded?

And no I have never used one nor needed to use one.

Post by **bruiser** » Fri Sep 15, 2006 10:56 am

Spud76 wrote:
Rb25sil80 wrote: If the ally ones are spining on your bar what makes you think steel won't??

They are not spinning but I had to tighten them that much that they bend around the bar before they stoped spinning. I have also put electrical tape behind to help. Not only this but the rod makes them bounce, bend as well.

Post by **Spud76** » Fri Sep 15, 2006 1:30 pm

bruiser wrote:
They are not spinning but I had to tighten them that much that they bend around the bar before they stoped spinning. I have also put electrical tape behind to help. Not only this but the rod makes them bounce, bend as well.

Thats all I done was wrap tape around where the u bolt clamps on never had a prob.
Be easy enough to knock up a steel set and get em powercoated or sprayed unless you want them shiney? Be a lot cheaper than stainless and most metal fab joints would probably help you out.

Post by **dibbz** » Fri Sep 15, 2006 3:26 pm

I just put some clear tube around the u bolts on my aluminium one and it is fine. Same thing as the tape, you shoudln't have to tighten the hell out of them :)

Post by **phippsey** » Sun Sep 17, 2006 2:16 am

Just weld it to the bar. Welding's the new bolt-on.

Have you thought about composite fibre rod holders?

Post by **Shadow** » Sun Sep 17, 2006 10:09 am

phippsey wrote:Just weld it to the bar. Welding's the new bolt-on.

Have you thought about composite fibre rod holders?

which would make your bullbar illegal.

Post by **phippsey** » Mon Sep 18, 2006 3:12 pm

just lift ya dress a little when they pull you ova and it'll be rite

Outer Limits 4x4 Board

Rod Holders

Rod Holders

holders

Who is online