Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

8274 Remote Wiring

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
User avatar
Dak
Posts: 67
Joined: Thu Oct 27, 2005 2:50 pm
Location: Wanganui, NZ

Contact:
Contact Dak

8274 Remote Wiring

Post by Dak »

Hiya all, can someone help out with wiring so I can run an in cab remote? I have a 8274 with the 5 pin hand controller. I already have an in cab switch to isolate the winch but need to wire up an in-out switch. None of the sites i've found so far have diagrams that work.

Cheers, Jeff.
Top
Posts: 2944
Joined: Tue Feb 11, 2003 5:47 pm
Location: Manjimup, Western Australia

Contact:
Contact ausyota

Post by ausyota »

Does this help?
Image
R.I.P Brock Fontanini 28-3-06 - 16-2-08
www.teamcarnage.net
Top
Posts: 469
Joined: Fri Sep 10, 2004 1:45 pm
Location: Melb

Post by sootygu »

Try this link, very good info.

http://www.equip4.co.nz/WINCHC~1.HTM
Top
User avatar
Dak
Posts: 67
Joined: Thu Oct 27, 2005 2:50 pm
Location: Wanganui, NZ

Contact:
Contact Dak

Post by Dak »

Cheers, but neither of those two are any good. I have a late model 8274 which has sealed solenoids which are different, I just need to know which terminals on which solenoids to fed the switch to.

Cheers, Jeff.
Top
Posts: 9
Joined: Wed Oct 25, 2006 8:39 pm

Post by Titan Offroad »

What sort of solenoids Jeff, I may be able to help you. Can you post up a pic or email me one at titan_offroad@hotmail.com then I might be able to tell you which way to go.
Titan Solenoids and Winch Rope - competition tested and proven!
Top
User avatar
Dak
Posts: 67
Joined: Thu Oct 27, 2005 2:50 pm
Location: Wanganui, NZ

Contact:
Contact Dak

Post by Dak »

Cheers, I will post up a pic tonight.

Cheers, Jeff.
Top
User avatar
Dak
Posts: 67
Joined: Thu Oct 27, 2005 2:50 pm
Location: Wanganui, NZ

Contact:
Contact Dak

Post by Dak »

Pic of the solenoid pack

Image

Cheers, Jeff.
Top
Posts: 207
Joined: Thu Aug 26, 2004 11:14 am
Location: Queensland,Clontarf

Post by Hales231271 »

The 5pin wirring are set up so there is a floating earth.
When you use the controller it completes an earth to the solenoids and supplies 12V to either the 2 in or 2 out solenoids.

Run a wire from the earth side of one of the solenoids to inside cab isolator switch.Other side of swith to earth point chasis etc....

Run power via fuse to moment in/out swith.
Can't remember the colors but one side of the switch to green wire on out solenoids.Other side of switch to white wire on in solenoids.Someone can correct me on this.


The winch will not work unless your ground isolator switch is on.
The standard 5 pin connector is not changed.

Cheers
Dazza
Top
User avatar
Dak
Posts: 67
Joined: Thu Oct 27, 2005 2:50 pm
Location: Wanganui, NZ

Contact:
Contact Dak

Post by Dak »

Cheers, got it sussed, the terminal on the top left of the pic hidden under the red battery cable is the one to earth, the two lowest terminals are the in and out ones, thanks for the help people.

Cheers, Jeff.
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 0 guests