My sons series 11a oz army workshop 109 is in need of tyres,
I am contemplating retiring the 9/34 swampers from my rangie and instead of selling them for bugger all, putting them on the series.
My concern is that they may be too big for the driveline.
It gets only occasional use on medium tracks, but I have broken 2 axels on 750/16/s but I used to take it on hard trips.
To all the toy people out there; are series diffs a straight swap?
I am trying to do every thing on this vehicle on a shoe string budget .
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
34's on 11a drive train
Moderator: Micka
34's on 11a drive train
out of my mind, back soon.
If it's not used on anything but medium tracks it would be fine.
IN fact it will raise the on road cruise speed to be quite useful. And with 1st being as low as it is you will still be able to take off on hills.
To put Hilux diffs under it wouldn't be too hard, except you would have to change the spring seats and new u-bolts and possible have to make some new flip plates and a hi steer setup for the drag link.. Good idea if you want to spring over. they would almost boltr straight in, redrill the diff flanges for rove and make a drag link and hi steer.
But As I said for the use to are intending the SII would be fine, and at worst it WILL break an axle before a CWP
IN fact it will raise the on road cruise speed to be quite useful. And with 1st being as low as it is you will still be able to take off on hills.
To put Hilux diffs under it wouldn't be too hard, except you would have to change the spring seats and new u-bolts and possible have to make some new flip plates and a hi steer setup for the drag link.. Good idea if you want to spring over. they would almost boltr straight in, redrill the diff flanges for rove and make a drag link and hi steer.
But As I said for the use to are intending the SII would be fine, and at worst it WILL break an axle before a CWP
[i]DAS[/i]
MY05 4.4L V8 Range Rover Vogue
Series 2a Buggy....In the Building
MY05 4.4L V8 Range Rover Vogue
Series 2a Buggy....In the Building
34's on 11a drive train
My main concern is rear axle strength, and I don't want to modify the thing much , the young fella is only 4yr old and by the time he can drive it on the road it will be celebrating it's 57th birthday.
Maybe an early manually locking jac mac would be a solution .
Maybe an early manually locking jac mac would be a solution .
out of my mind, back soon.
Re: 34's on 11a drive train
will you adopt me so I can drive this nowswamp wrote:…the young fella is only 4yr old…
Ransom note = demand + collage
The bolt operated McNamara diff lock will strengthen up the rear diff a lot! My brother had a ex army IIA LWB with a 253 and a bolt operated diff lock, and didn't start breaking things until he put 36" Silverstones on, then he started spitting crown wheels left right and centre. Eventually he fitted a McNamara hypoid rear diff, and that cured the problem.
If anyone tells you to put a Salisbury diff in, just don't put the 34's on, as you will have roughly the same ground clearance as with the 7.50x16's and the rover diff.
Regards
Craig Murray
If anyone tells you to put a Salisbury diff in, just don't put the 34's on, as you will have roughly the same ground clearance as with the 7.50x16's and the rover diff.
Regards
Craig Murray
Who is online
Users browsing this forum: No registered users and 3 guests